How to Remove Grout Haze From a New Tile Floor With an Auto Scrubber
How to remove cement grout haze from a new tile floor with an auto scrubber: wait for the grout to cure, wet the joints, mop on an acid haze remover, let it dwell, then scrub and pick up. Six labels and two tile makers compared.
Key takeaways
- Try hot water, detergent and a nylon pad or brush first. Crossville and Marazzi both say a scrub like that often cleans a new floor, and that acid is a last step, not the first.
- Before any acid, let the cement grout cure. Crossville says usually 7 to 10 days, Aqua Mix at least 10, Marazzi usually 14 to 21. If you cannot find out, 21 days meets all three.
- Soak the grout joints with plain water, spread the haze remover by mop, keep it wet for the label's time (1 to 15 minutes across the sheets we read), then scrub and pick up at once. Rinse and pick up again.
- Do not pour acid into the solution tank unless both labels allow it. Only Kärcher's RM 751 lists scrubber driers. The Tornado BD 14/4 manual says do not use acid solutions in the machine.
- Acid is the wrong product for epoxy grout, premixed grout and latex grout, and for marble, limestone and travertine. Ask the grout maker which product to use.
Let the cement grout cure first. Then wet the joints, mop on an acid grout haze remover and let it work. Scrub with a nylon brush or white pad, and pick it all up. Crossville tells crews to give the haze remover "adequate dwell (10 to 15 minutes) time prior to floor scrubbing." Then they scrub, pick up the dirty slurry with a wet vacuum, and rinse twice. An auto scrubber is a wet vacuum with a brush in front of it, so it fits that job well.
The wait is where most people go wrong. Crossville says to wait until the grout joint has fully cured, "usually 7 to 10 days before using acidic cleaners." Aqua Mix says at least 10 days. Marazzi says "usually 14 to 21 days." The haze looks ready to come off on day two. The grout under it is not ready for acid.
What grout haze is
Grout haze is a thin film of grout left on the face of the tile after the joints are filled and sponged. Crossville calls it a "grout film." It warns that a new floor with it "can have a dull appearance," and light tile "will appear dirty from the start." It also traps the dust and dirt of the building site.
Cement haze is the same film from cement grout or mortar. Most haze removers are sold for this kind. Aqua Mix calls its product "an acidic treatment designed to remove cementitious grout haze."
A few more terms come up on every label:
- Cure. The days a cement grout needs to harden all the way through. The grout feels hard much sooner than it is cured.
- Acidic haze remover. A cleaner with a low pH that dissolves the cement in the film. Kärcher's RM 751 is pH 0.7 as sold, and Lithofin's KF is below 1. Our floor cleaner pH guide explains the scale.
- Pre-wetting. Soaking the floor and the grout joints with plain water before the acid goes down. Every maker in this article asks for it.
- Dwell. How long the remover stays wet on the floor before you scrub and pick it up.
- Latex or polymer grout. Cement grout with a polymer added. Crossville and Marazzi treat it differently from plain cement grout, as you will see below.
Two answers circulate: minutes or weeks
One answer says remove haze within minutes, before it sets. The other says wait one to three weeks. Both come from real makers. They answer different questions.
The short answer is about fresh grout, during the install. Fila tells tile setters to let "fresh grout residues" set "for 10 to 30 minutes," then wipe with a damp sponge and use its Instant Remover. Fila says that product "is suitable only during installation; for cured grout, opt for DETERDEK PRO." A JLC forum moderator says floor machines on big commercial jobs "are usually employed a day or two after the grout has been installed." Neither of those is an acid step on cured grout.
The long answer is about acid. Crossville's 7 to 10 days, Aqua Mix's 10 days and Marazzi's 14 to 21 days are all waits before an acid cleaner. Mapei's sheet says the grout "should be fully cured according to the manufacturer's specifications."
So here is the ruling. A crew that arrives with a scrubber after the setters leave is past the 30 minute window. The haze has set. If plain water and detergent will not take it off, the acid has to wait for the cure date on the grout bag. If you cannot find that date, wait 21 days. That meets every figure above.
Try detergent first
Both tile makers put acid last. Crossville says that in most cases its tile "can be cleaned successfully by scrubbing the installation with hot water and a neutral detergent," then rinsing and wet vacuuming. It says "Acid washing is rarely recommended, and is not usually necessary" if the cleaning is done in time.
Marazzi says the same. Its commercial floors "can be cleaned successfully by scrubbing the installation with hot water and detergent," then rinsing and wet vacuuming. For more aggressive cleaning, "floor scrubbing machines equipped with nylon pads or brushes should be used."
That first pass is ordinary scrubber work. Use a neutral cleaner from our neutral cleaners guide and a nylon brush or pad. If the floor dries clear, you are done. If a dull film comes back as the floor dries, that is cured haze, and the rest of this page applies.
Six haze remover labels compared
We read each maker's data sheet, and for Deterdek Pro, Fila's own blog post. The table shows what each one prints.
| Product | pH as sold | Dilution | How it goes on | Dwell | Pad or brush | Grout cure stated | Not for |
|---|---|---|---|---|---|---|---|
| Kärcher FloorPro RM 751 | 0.7 | 5 to 25% for deep cleaning | Scrubber drier or by hand; "Soak any cement joints thoroughly" | 1 to 5 minutes | "Appropriate brush/roller/pad" | Not stated | Polished marble, acid sensitive materials |
| Aqua Mix Cement Grout Haze Remover | Not stated | 1:3 for light haze, up to full strength for heavy | On a pre-wet surface, small areas | Flush "immediately after brushing" | White nylon bristle brush | At least 10 days | Epoxy or premixed grout haze; marble, limestone, travertine |
| Mapei UltraCare Acidic Tile & Grout Cleaner | Not stated | 1:10 light, 1:5 moderate, 1:2 heavy (cleaner to water) | Paint brush, mop, sponge or paint pad; "Do not apply with a sprayer" | 2 to 5 minutes | Soft brush or white pad, test first | "Fully cured" per grout maker | Polished marble, limestone and concrete |
| Fila Deterdek (US) | Not stated | 1:5 after installation | On wet surface and joints, a few square feet at a time | "A few minutes" | Abrasive pad or large brush, then wet vac | Not stated | Marble, limestone, travertine |
| Fila Deterdek Pro | Not stated | 1:5 to 1:10 | Spread on a few square meters at a time | 5 minutes | Stiff brush or single disc machine with pad | Not stated | Epoxy grout (Fila names CR10 instead) |
| Lithofin KF Cement Residue Remover | Below 1 | About 1:4, down to 1:15 for cement grout | On wet surface by mop, white pad or brush | 10 minutes | White pad or scrubbing brush, then wet vac | Not stated | Marble, limestone, enamel, zinc |
Two tile makers add their own rules. Crossville gives the 10 to 15 minute dwell and names a "heavy (75 to 90 lb. head weight) swing type floor scrubber" with a "heavy duty Green floor stripping pad." Marazzi says to use only "sulfamic acid or phosphoric acid" products, mixed to the maker's directions.
Which pad to fit
The labels split in two. Aqua Mix, Mapei and Lithofin name a white pad or a white or soft brush. Fila asks for something tougher: an abrasive pad or a large brush for Deterdek, and a stiff brush for Deterdek Pro. Marazzi names nylon pads or brushes. Mapei asks you to test a small area first "to make sure that a brush or pad will not scratch the surface." So start with the white pad or nylon brush, and step up only if the test spot stays hazy. Crossville's green stripping pad is its rule for its own porcelain, so use it only where the tile maker names it. Our brushes and pads guide shows where each pad color sits.
Acid in the tank: check both labels
Only one product in the table names the machine. Kärcher lists "scrubber driers" as a way to use RM 751, mixed with fresh water at the right dose. Every other label spreads the product by mop, brush, sponge or pad. Mapei bans sprayers outright.
The machine has a say too. The Tornado BD 14/4 manual says "Do not use acid solutions which could damage the machine and/or the persons," and "Never use pure acid." So acid goes in the tank only if the chemical label lists scrubber driers and the machine manual allows acid. If either one is silent, mop it on. Then run the scrubber with clean water only. Afterward, flush the tank, pump and lines with clean water.
Mopping on also solves the timing. A scrubber with its squeegee down picks up solution right behind the brush. That is far less than the 1 to 15 minutes the labels that give a time ask for. Lay the product down first, or make the first pass with the squeegee up.
Worked example: a 2,000 sq ft porcelain lobby
Take a new 2,000 sq ft lobby of Crossville porcelain with plain cement grout. The setters left a dull film. Suppose the crew uses Fila Deterdek, a walk-behind scrubber and a white pad. Here is how the labels would have you run it.
- Try detergent first. Scrub with hot water and a neutral cleaner, as Crossville and Marazzi describe. Suppose a film still shows once the floor dries.
- Wait for the cure. Crossville says usually 7 to 10 days before acid. Suppose the grout bag gives no other figure, so the crew waits until day 10.
- Mix the product. Fila's sheet gives 1,630 sq ft per gallon at 1:5 on porcelain. 2,000 divided by 1,630 is about 1.23 gallons of Deterdek. At 1 part product to 5 parts water, that is about 6.1 gallons of water, or about 7.4 gallons of mix. Mix it in a bucket, not the tank.
- Soak the joints. Run the scrubber over the floor with clean water and the squeegee up. Crossville wants the joints "thoroughly saturated with water first."
- Mop it on in sections. Do only as much floor as you can scrub before the product dries. Kärcher and Mapei both say not to let it dry on the surface, and Aqua Mix says to work in small areas.
- Let it dwell. Deterdek says "a few minutes." Crossville allows its remover 10 to 15. Keep the section wet.
- Scrub and pick up. Run the scrubber with clean water and the squeegee down. Crossville says "DO NOT MOP," because a mop only spreads the slurry around.
- Rinse twice. Crossville says to rinse and pick up again, "possibly twice," so no slurry or cleaner is left.
Now change one fact. Suppose the grout is epoxy. Deterdek is the wrong product. Crossville's chart lists separate epoxy haze removers, such as Fila's EPOXYOFF and Mapei's Epoxy Grout Haze Remover. Fila's blog names CR10 for epoxy grout. The scrubber steps stay much the same, but the bottle changes.
Which product for which floor
This table restates the rulings above, with the source for each.
| Situation | What to use | Source |
|---|---|---|
| Any new tile floor, first attempt | Hot water, detergent, nylon pad or brush | Crossville, Marazzi |
| Cured cement grout, haze still there | Acid haze remover after the cure wait | Crossville, Marazzi, Aqua Mix |
| Cement grout not yet cured | No acid; wait for the date on the grout bag | Crossville, Aqua Mix, Marazzi |
| Latex or polymer modified grout | The cleaner the grout maker recommends | Crossville, Marazzi |
| Epoxy grout | An epoxy haze remover, not a cement one | Crossville chart, Fila, Aqua Mix |
| Premixed or ready to use grout | Typically an alkaline or specialty cleaner, per the grout maker | Crossville, Aqua Mix |
| Marble, limestone, travertine | No acid haze remover | Aqua Mix, Fila, Lithofin, Mapei |
The latex row needs a word. Crossville and Marazzi both warn that "grouts which contain latex can actually bond more strongly" to the tile if cleaned with acid. Read the grout bag before you pick a remover.
What this answer does not cover
This page covers cement grout haze on new ceramic, porcelain and quarry tile. It does not cover acid sensitive stone. Aqua Mix warns that acids "may etch, lighten, or change the color of" cement, metallic glazes and stones "such as marble, limestone, travertine and some basalts." Our terrazzo and natural stone guide covers those floors. Lithofin also names enamel and zinc. If a tile has a metallic glaze or the trim is zinc, keep acid off it. The cure times here are from these documents only, and the grout bag on your job overrides them. These products are strong. Kärcher's RM 751 "Causes severe skin burns and eye damage," so read the safety data sheet and wear the gloves and eye protection it names. Your machine manual still decides what goes in the tank. A soft white powder that grows back in the joints weeks later is not haze. By the Ceramic Tile Education Foundation's test it is efflorescence, which our guide to removing efflorescence covers. If a haze comes back after a rinse, check the rinse first. Crossville warns that cleaning solution left to dry forms a coating "which is very difficult to remove." Our residue and rinsing guide covers it.
Once the haze is off, the floor joins the normal routine in our ceramic tile and grout guide. If the same job also laid vinyl, our guide to scrubbing a new vinyl floor gives that floor's wait.
Frequently asked questions
How long after grouting can you remove grout haze?
During the install, Fila lets fresh residue set 10 to 30 minutes, then sponges it off and uses its Instant Remover. For acid on cured haze, wait usually 7 to 10 days (Crossville), at least 10 (Aqua Mix) or usually 14 to 21 (Marazzi). The grout bag decides.
Can I put grout haze remover in my auto scrubber's tank?
Only if the remover's label lists scrubber driers and your machine manual allows acid. Kärcher's RM 751 lists scrubber driers. The others we read go on by mop, brush or pad. Tornado's BD 14/4 manual says not to use acid solutions.
What pad removes grout haze with a floor scrubber?
Aqua Mix, Mapei and Lithofin name a white pad or a white or soft brush. Fila names an abrasive pad or a stiff brush. Crossville names a green stripping pad on a heavy swing machine for its own porcelain. Test a small area first.
Will a cement grout haze remover take off epoxy grout haze?
No. Aqua Mix says not to use its cement remover on epoxy or premixed grout haze. Crossville lists separate epoxy products, and Fila names CR10.
Why did the haze come back after I scrubbed?
The detergent may have lifted only loose dirt, leaving set haze behind. Or cleaning solution may have dried on the floor. Crossville says dirty solution left to dry forms a coating, so rinse and pick up twice.
Sources
- Crossville, Porcelain Stone Care & Maintenance Guide, LIT-MN-22 (file dated 06-17-23): crossville.com
- Marazzi USA, Commercial Installation and Maintenance Recommendations (9/14/12): daltile.com
- Kärcher, FloorPro Deep Cleaner, acidic RM 751 (0.011-136.0, 2025-01-27): cleanstore.co.uk
- Custom Building Products, Aqua Mix Cement Grout Haze Remover, TDS-313 (October 20, 2021): custombuildingproducts.com
- Mapei, UltraCare Acidic Tile & Grout Cleaner technical data sheet (edition March 30, 2017): contractorsdirect.com
- Fila, Deterdek cementitious grout haze remover (US): contractorsdirect.com
- Fila, Mastering the End-of-Work Clean (December 19, 2023): filasolutions.com
- Lithofin, KF Cement Residue Remover technical information: lithofin tech sheet
- Tornado Industries, BD 14/4 Compact Auto-Scrubber manual, Form L9740 DA 05/20: sylvane.com
- Journal of Light Construction, Removing Grout Haze (forum Q&A): jlconline.com