Floor Types

How to Remove Efflorescence From a Tile or Concrete Floor With an Auto Scrubber

How to remove efflorescence from a tile or concrete floor with an auto scrubber: brush it off dry, find the water, then scrub with a remover made for it and pick up at once. Seven labels compared on pH, dilution, dwell and coverage.

Key takeaways

  • Brush it off dry first. Efflorescence is a soft white powder that CTEF says can be brushed away, and LATICRETE says a dry white nylon pad often takes off most of it.
  • Find the water before you scrub. Efflorescence needs salts, water and evaporation, and the salts are in every cement product, so water is the part you can stop. If you do not, it comes back.
  • Only then use a remover, on what the dry pass left. Across seven labels the dwell runs from one minute (Quikrete) to 60 minutes (Aqua Mix Eff-Ex), so follow your own label. Pick up with the squeegee down and keep the rinse light.
  • Only PROSOCO PreKlean is written to go in a scrubber tank, and it is for new slabs after blanket curing. Mop or brush the others on, then scrub and pick up.
  • No acid on polished concrete or polished stone. Ask the grout maker before acid touches cement grout. Hard white residue is not efflorescence at all, and needs a different product.

Brush it off dry first. Then find and fix the water that brought it up. Only after that, scrub what is left with a remover made for efflorescence, and pick the water up at once. The Ceramic Tile Education Foundation (CTEF) says efflorescence "is normally a soft powdery material that can be brushed away." LATICRETE says a dry white nylon pad "oftentimes" removes most of it. What the dry pass leaves, a remover and an auto scrubber can take off.

There is a catch. A scrubber puts water on the floor, and water is what carries the salts up. So run it with the squeegee down, and rinse only enough to lift the cleaner. If the white comes back within days, the floor is not dirty. It is wet underneath, and no cleaner fixes that.

What efflorescence is

Efflorescence is salt left on the face of concrete, grout, tile or brick after water dries off it. LATICRETE calls it "a white crystalline deposit which is composed of salts, lime and/or other soluble minerals." The word is French for "to flower out." CTEF notes it is also called "new building bloom."

CTEF quotes the Portland Cement Association on what it takes. Three things must happen together:

  • Salts in the concrete, mortar, grout or brick.
  • Water to dissolve the salts and carry them to the surface.
  • Evaporation, or water pressure from below, to move that water.

"If any one of these conditions is eliminated, efflorescence will not occur." LATICRETE says the salts are in portland cement products from the way cement is made. So every slab, mortar bed and cement grout has them. Water is the one part you can control.

A TileLetter webinar recap adds a second kind. In secondary efflorescence, the salts come from outside and soak in. It names de-icing salts as an example. On a floor by a door, that is the ice melt tracked in all winter. Our ice melt residue guide covers that film.

White films that are not efflorescence

Some other white films look the same and need a different product:

  • White scum. PROSOCO describes it as hard white or gray deposits on clay brick or tile. It is "not water-soluble," unlike efflorescence, which "can normally be brushed away or easily washed off."
  • Latex migration. Latex from the mortar or grout, carried up by water. CTEF gives one test. If the residue is soft and powdery, it is efflorescence. If it is hard, it is latex, which "can be difficult to remove." CTEF says to ask the grout maker what to use.
  • Grout haze. A film of cement grout left on new tile by the setters. Our grout haze guide covers it.
  • Laitance. A weak, dusty layer of fine cement on a new slab. PROSOCO sells its PreKlean for laitance and "residual surface salts" together.

So the first check costs nothing. Rub the white with a dry, stiff brush. If it powders off, CTEF's test says efflorescence. If it is hard and will not move, read the latex and white scum notes before you buy anything.

Two answers circulate: acid wash it, or keep it dry

Search this question and you get two kinds of advice. One says acid wash the floor. The other says use as little water as you can. Both come from real sources. What matters is the order.

Most removers are acids. Dumond's is pH below 1. PROSOCO's Light Duty Concrete Cleaner is pH 1.14 at 1:2. LATICRETE explains why acid works: most efflorescence is lime and salts that "usually dissolve when in contact with acid."

But the same LATICRETE sheet warns about water. "Do not over apply rinse water. Water is one of the key factors in the development of efflorescence." CTEF warns that a steam cleaner "may bring the salts to the surface more quickly and in increased quantities."

Here is the ruling. Dry first, remover second, and never more water than the machine picks up. A dry pad adds no water at all. A remover comes next, and only on what the dry pass left. An auto scrubber fits that second step when its squeegee is down, because the vacuum lifts the water right behind the brush.

CTEF made the same point to a church. It had laid about 13,000 sq ft of tile, most of the grout had turned white, and it had just bought a large walk-behind scrubber. It asked what solution to put in it. One of CTEF's questions back was, "Does the scrubber also vacuum the water from the surface as it cleans?"

Find the water before you scrub

CTEF's reader letters keep making one point: the white keeps coming back until the water stops. In one case, a stone wall's grout was cleaned with "a very mild acid solution and a bristle brush." It worked for a little while. Then the salts came back. The cause was roof flashing that let rain into the wall. Once the roofer fixed it, the tile setter washed the salts off, and the efflorescence disappeared.

On a floor, CTEF's questions point to these sources:

  • Ground moisture under a slab on grade. CTEF asks whether a vapor barrier went under the concrete.
  • Leaks from water lines, pool lines or a shower pan.
  • A new or remodeled job that is still drying out.
  • A covering that traps vapor. In one basement, moisture had escaped through carpet for years. Plastic floor tiles laid in its place trapped it.

TileLetter's experts say there is no accepted industry standard for efflorescence. They add that once it shows up, "it may not ever go away fully." Cleaning manages the white. Fixing the water ends it.

Sealing does not fix it either. CTEF says a breathable sealer "may slow down the moisture travel through the system, but it will not solve the issue." LATICRETE says a penetrating sealer after cleaning "should minimize" the white coming back. It also says efflorescence "may occur again" if the three causes are not dealt with, "even if a suitable sealer is used." So seal after the water is fixed, never instead.

Seven labels compared

We read seven makers' current sheets. This table shows what each one prints. Coverage is per gallon of concentrate unless noted.

ProductMade forpHDilutionDwellHow it goes onCoverage
PROSOCO Consolideck PreKleanNew concrete floors: laitance and surface salts4.81:4Average 15 minutesAuto scrubber, squeegee up; also mop or low-pressure sprayer600 to 1,200 sq ft
PROSOCO Sure Klean Light Duty Concrete CleanerConcrete, brick, pavers, concrete tile. Not fired clay tile or polished marble, limestone or travertine1.14 at 1:21:2 to 1:63 to 5 minutesMasonry brush or spray at 50 psi or less300 to 600 sq ft on concrete
PROSOCO Sure Klean White Scum RemoverWhite scum on clay brick and tile only1.6 at 1:11:12 to 3 minutesSpray, brush or roller100 to 200 sq ft on clay tile
Fila Deterdek (US)Porcelain, ceramic, quarry tile, terracotta, acid-resistant stoneNot stated1:5 after install; 1:10 outdoors"A few minutes"On a wet floor; abrasive pad or large brush, then wet vac1,630 sq ft on porcelain at 1:5
Quikrete Efflorescence & Rust RemoverConcrete, pavers, brick, masonry, stuccoNot stated1:4, up to 1:1One minuteBrush or spray; nylon brush for heavy deposits100 to 200 sq ft per gallon jug
Dumond Smart 'n Easy Efflorescence RemoverNon-polished masonry: concrete, brick, pavers, block, travertineBelow 1Not stated15 to 30 minutes minimumLow-pressure sprayer; nylon brush if needed200 to 250 sq ft
Aqua Mix Eff-ExPorcelain, quarry, saltillo, terra-cotta, natural stone, porous tile and grout. Not polished marble, limestone or travertine7.4Undiluted30 to 60 minutesMop, sponge, roller or brush; agitate "with scrub brush or scrub machine"30 to 125 sq ft

Only two labels name a machine. PreKlean is "Ideal for auto-scrubber machines" and goes in the tank. Eff-Ex goes on by mop or roller, then you agitate it with a brush or a scrub machine. Deterdek says to pick up with a wet vac, which is what a scrubber's squeegee and vacuum are. The rest are wall and paver products, put on by brush or low-pressure spray.

Dwell runs from one minute to 60 across the table. So a dwell from one label means nothing on another. Read your own bottle.

White Scum Remover is in the table as a warning. It treats white scum, not efflorescence. PROSOCO also says it is "Not for use on concrete, cementitious surfaces, stucco or natural stone." Cement grout is a cementitious surface, so the label rules out grout joints too.

Only Eff-Ex is not an acid. It is also the thirstiest, at 30 to 125 sq ft per gallon used full strength. The worked example below shows what that costs on a big floor.

Concrete floors: dry first, then the mildest product

LATICRETE lists concrete as acid sensitive, alongside marble, limestone and travertine. Its method for those surfaces is a dry white nylon pad, by hand or on a rotary machine. If that fails, the next step is mechanical refinishing. It allows its acid cleaner on an acid-sensitive surface only if the surface is already textured and a test area looks right.

Concrete product makers do sell acid removers for concrete. Quikrete lists horizontal concrete. PROSOCO says its Light Duty Concrete Cleaner removes efflorescence from "new concrete." Both warn about etching. Quikrete says stronger mixes "may cause etching, particularly when left in contact for longer times." Even PreKlean, at a mild pH 4.8, carries the line "Significantly extended dwell times may etch the floor."

So on bare concrete, make the dry pass, then test the mildest product at its label dwell on a small patch. Let it dry before you judge it. LATICRETE says to let the surface "completely dry to determine the desired results." PROSOCO's concrete cleaner sheet asks you to let a test area dry 3 to 7 days before you approve it.

Finished concrete changes the answer:

  • Polished concrete. No acid. Our polished concrete guide says even mild acids etch the cement paste. PROSOCO's cleaner warns that acid "may damage polished masonry." Dumond limits its remover to non-polished surfaces. Use the dry pad, and call a polishing contractor if that is not enough.
  • Sealed concrete. Our sealed concrete guide treats efflorescence as a spot job with a product made for it, then a full pickup.

A new slab after blanket curing

This is the one case where a remover goes in the tank by design. PROSOCO's PreKlean sheet tells you to scrub and vacuum with clean water as the curing blankets come off. Its note: "do not allow surface salts to dry on the surface as blankets are being removed."

Then fill the tank with water first and add PreKlean at 1:4. Scrub with the squeegee up, over only as much floor as you can clean "within 10–15 minutes." The average dwell is 15 minutes. Scrub again while the vacuum picks it up, then rinse with clean water. PROSOCO notes that a second scrubber for rinsing speeds the job up. Our guide to scrubbing new concrete covers when the slab can carry the machine.

Tile floors: the grout decides

Porcelain and ceramic tile take acid well. Deterdek lists them, along with quarry tile and terracotta. The grout is the question. CTEF's advice is direct: "Only use an acid cleaner if the manufacturer makes that recommendation." That means the grout maker. Our ceramic tile and grout guide explains why repeated acid slowly wears cement grout away.

Eff-Ex is the non-acid route. Custom Building Products says not to dilute it. Pre-wet the floor, but take up any puddles first. Spread it by mop or roller and let it dwell 30 to 60 minutes. Do not let it dry; add more if it starts to. Agitate, rinse with clean water, and wet vacuum. Custom says to let the floor dry 24 hours before sealing. Eff-Ex also has an inhibit mode: a thin coat scrubbed in and not rinsed, repeated two or three times.

For the pad, LATICRETE names a white nylon pad or stiff white nylon brush. It warns that colored pads "can lead to color bleeding in the substrate." Our brushes and pads guide shows where white sits.

Only PreKlean is written for the tank. Put the others on by mop or brush, and run the scrubber on clean water to agitate and pick up. Our grout haze guide explains why the machine manual has a say on acid in the tank as well.

Worked example: the 13,000 sq ft church floor

Take the church that wrote to CTEF. It has about 13,000 sq ft of new tile with cement grout, mostly white, and a large walk-behind. Nobody tested this. It is the labels' own figures worked through.

  1. Find the water. Ask CTEF's questions. Is the job new or remodeled? What is under the tile? Is the slab on grade? Was a vapor barrier laid under it? Suppose it is new tile on a slab on grade, and the leak checks find nothing.
  2. Make the dry pass. Run a dry white nylon pad over the white areas, LATICRETE's first step. Pick up the loose powder. Suppose a third of the floor, about 4,333 sq ft, still shows white.
  3. Ask the grout maker. Per CTEF, acid touches the grout only if the grout maker says so.
  4. Work out the product. If acid is approved, Fila's Deterdek covers 1,630 sq ft per gallon at 1:5 on porcelain. 4,333 divided by 1,630 is about 2.7 gallons, plus about 13 gallons of water. If acid is not approved, Eff-Ex at 30 to 125 sq ft per gallon needs about 35 to 144 gallons, used full strength. Over the whole 13,000 sq ft, that would be 104 to 433 gallons. The dry pass is what keeps that number small.
  5. Apply in sections. Deterdek goes on a wet floor, "a few square feet at a time." Let it sit "a few minutes." Eff-Ex sits 30 to 60. Keep each section wet.
  6. Scrub and pick up. Run the scrubber with a white pad or white nylon brush, clean water in the tank and the squeegee down.
  7. Rinse lightly. One clean water pass, squeegee down. LATICRETE says rinse "well enough to remove any cleaner residues only."
  8. Let it dry, then look. If white returns within days, go back to step 1.

Now change one fact. Suppose the church floor were polished concrete instead. No product in the table applies. The dry pad is the whole method, and if it fails, the next call is a polishing contractor.

Which method for which floor

This table restates the rulings above, with the source for each.

FloorFirst stepIf white remainsSource
Any floorDry brush or dry white pad; find the waterRemover made for the surface, then pick up at onceCTEF, LATICRETE
New slab after blanket curingClean water scrub as the blankets come offPreKlean 1:4 in the tank, squeegee up, about 15 minutesPROSOCO
Bare concrete in useDry white padAcid remover labeled for concrete, after a test patchQuikrete, PROSOCO, LATICRETE
Polished concreteDry white padRefinishing, no acidLATICRETE, PROSOCO
Porcelain or ceramic, cement groutDry white padAcid (such as Deterdek) only if the grout maker agrees; Eff-Ex if notCTEF, Fila, Custom
Polished marble, limestone, travertineDry white padRefinishing; no Eff-Ex, no acidLATICRETE, Custom, Fila
Hard white film on clay brick or tileCheck it is white scumWhite Scum Remover, never on concrete or groutPROSOCO
Hard white film in tile groutTreat as latex migrationThe grout maker's productCTEF

What this answer does not cover

This page is about efflorescence on floors you can scrub. It does not find the water for you. A slab that keeps blooming needs the source traced, and that may mean a plumber, a roofer or a moisture test by a flooring pro. If you are not sure what the white is, CTEF suggests having a sample analyzed at a local testing lab. These removers are strong. Dumond's label says "CAUSES SKIN BURNS & EYE DAMAGE," and Quikrete warns never to mix its remover with bleach or other cleaners, since "poisonous gas" may form. Read each safety data sheet and wear what it names. CTEF adds that rinsing does not remove a strong acid's presence, and you may need to neutralize it with baking soda and water. Cold matters too. PreKlean is not for use below 40 F, Dumond wants 40 to 90 F, and Deterdek between 41 and 86 F. Acid rinse water has rules of its own; see our guide to where to dump scrubber water. For honed or textured stone, see our terrazzo and natural stone guide. Your grout bag and machine manual override anything here.

Frequently asked questions

Can you remove efflorescence with just water?

Often, yes. PROSOCO says efflorescence "can normally be brushed away or easily washed off." But water also feeds it, so start with a dry brush or dry white pad. If you wash, pick the water up at once with the squeegee down.

Why does efflorescence keep coming back after I clean it?

Water is still reaching the floor from below or inside. CTEF says to find the source and fix it, or the salts keep coming up. TileLetter's experts say it "may not ever go away fully" until then.

Can I put efflorescence remover in my auto scrubber's tank?

Only if the label says so. Of the seven we read, only PROSOCO's PreKlean is written for the tank, water first and then product at 1:4. Mop or brush the others on, then scrub with clean water.

Does sealing stop efflorescence?

Not on its own. CTEF says a breathable sealer may slow the moisture "but it will not solve the issue." LATICRETE says it can still return "even if a suitable sealer is used." Seal after the water problem is fixed.

How long should efflorescence remover sit before scrubbing?

As long as its own label says. Quikrete says one minute, PROSOCO's concrete cleaner 3 to 5 minutes, PreKlean about 15, Dumond 15 to 30, and Eff-Ex 30 to 60. Do not let any of them dry on the floor.

Sources

  • PROSOCO, Consolideck PreKlean product data sheet (item #46040, 102517, 2017): prosoco.com
  • PROSOCO, Sure Klean Light Duty Concrete Cleaner product data sheet (item #10088, 113022, 2022): PROSOCO PDF
  • PROSOCO, Sure Klean White Scum Remover product data sheet (item #10100, 103015, 2015), via BuildSite: buildsite.com
  • Fila, Deterdek cementitious grout haze remover (US): contractorsdirect.com
  • Quikrete, Taming the Efflorescence Monster: quikrete.com
  • Quikrete, Efflorescence & Rust Remover No. 8675-33 data sheet: quikrete.com
  • Dumond, Smart 'n Easy Efflorescence Remover technical data sheet (updated 2023-09-27): Dumond PDF
  • Custom Building Products, Aqua Mix Eff-Ex, TDS-169 (published October 20, 2021): custombuildingproducts.com
  • LATICRETE, TDS 159 Efflorescence: Causes, Prevention and Removal (rev. July 23, 2026): laticrete.com
  • Scott Carothers, Ceramic Tile Education Foundation, Understanding Efflorescence aka that Ugly White Powder on Your Tile (September 12, 2023): ceramictilefoundation.org
  • TileLetter, Ask the Experts: Efflorescence (August 1, 2023): tileletter.com
  • TileLetter, Efflorescence or latex migration: how to tell the difference, repair, and prevent (July 3, 2025): tileletter.com