Floor Types

How Long After Installing VCT, LVT or Vinyl Flooring Can You Scrub It?

How long after installing new VCT, LVT or vinyl flooring can you scrub it with an auto scrubber? The wait from 24 hours to 5 days or more, from 11 Armstrong, Mohawk, Interface, Milliken, Altro, Forbo, Tarkett and Gerflor documents, and why the foot traffic time is not the scrub time.

Key takeaways

  • Wait for the adhesive, not the floor. The 11 maker documents we read set 24 hours (Gerflor Tarasafe) to five days (Armstrong VCT, Milliken LVT, Tarkett Safetred, Forbo Marmoleum) before wet cleaning or machine scrubbing a glued floor.
  • If you do not know the maker, wait five days. That satisfies every document in our table except glue-down over a non-porous substrate, where Mohawk asks for "at least five days" and Forbo says more time "may be necessary."
  • The foot traffic time is not the scrub time. Mohawk allows foot traffic at 24 hours and scrubbing at 48; Milliken allows foot traffic at 12 to 24 hours and cleaning at 5 days.
  • Armstrong's current VCT sheet says five days. Its 2011 commercial guide said four, which is why both numbers circulate. Go by the current sheet.
  • Floating and loose lay floors have no adhesive wait: Mohawk says cleaning of floating LVT "may begin immediately," and Altro excludes loose lay floors from its 72 hours.

Between 24 hours and five days for a glued floor, depending on the maker, and five days if you do not know who made it. Armstrong's current VCT sheet says: "Do not wet wash, machine scrub, or strip the floor for at least five days after installation." Milliken, Tarkett and Forbo also say five days. Mohawk and Interface allow cleaning at 48 hours, Altro at 72 hours, and Gerflor's Tarasafe sheet at 24. A floating floor, with no glue under it, can be cleaned straight away.

The clock is the adhesive. Armstrong gives the reason in one line: "Excess moisture can interfere with the adhesive and/or seam treatments." Milliken says excess water "can migrate between flooring seams and contribute to adhesive failure," and Forbo asks for its wait "in order to allow the adhesive to dry and cure properly." The wear layer on a new vinyl floor is ready on day one. The glue under it is not, and an auto scrubber is the one cleaning tool that puts water, weight and a spinning pad on the floor at the same time.

The wait, maker by maker

We read the current or most recent maintenance document from each maker and copied three figures: when people may walk on the floor, when rolling loads may go on it, and when it may be wet cleaned or scrubbed.

Maker and documentFloorFoot trafficRolling loadsWet cleaning or machine scrubbing
Gerflor, Tarasafe ranges maintenance (May 2010)Safety vinylNot statedNot stated24 hours "before any cleaning is carried out"
Mohawk Group, floating and glue down LVT maintenance (2017)LVT, glue-down with M95.0 adhesive24 hours72 hours (heavy traffic, rolling loads, furniture)48 hours "before wet cleaning and scrubbing"
Mohawk Group, same documentLVT, MS160 spray adhesive1 hour24 hours48 hours
Mohawk Group, same documentLVT, glue-down over a non-porous substrateNot statedNot stated"At least five days"
Mohawk Group, same documentLVT, floatingImmediatelyNot statedImmediately
Interface, LVT maintenance guidelines (Rev. 12/15/2023)LVTNot statedNot stated48 hours "from the completion of installation to clean floor"
Altro, cleaning guide for LVT floors (Lavencia)LVTNot statedNot stated"Generally 72 hours"; loose lay excluded
Altro, cleaning guide for safety and slip-resistant floors (US, 2023)Safety vinylNot statedNot stated"Generally 72 hours"; XpressLay and loose lay excluded
Forbo, Safestep floor careSafety vinylNot statedNot statedNot "within 3 days of installation"
Armstrong, commercial resilient maintenance (F-8663-111, 2011)VCT, LVT, sheet vinyl, linoleumNot statedNot stated4 days
Armstrong (AHF), VCT maintenance instructions (Print# 7440F10737-926)VCT: Excelon, Stonetex, Imperial Texture, Safety ZoneNot stated72 hours"At least five days"
Forbo, Marmoleum with Topshield2 (US, v2.20, 10/13)LinoleumNot statedNot stated"A minimum of five days"; longer over non-porous substrates
Tarkett, Safetred maintenance (March 2012)Safety vinylNot statedNot stated"At least 5 days" before "any wet cleaning"
Milliken, LVT initial post installation maintenance guide (05/2020)LVT12 to 24 hours24 to 48 hours5 days

Eleven documents, eight makers, and a spread from one day to five. Nobody in the set says a glued vinyl floor can be scrubbed sooner than 24 hours, and nobody sets a longer fixed figure than five days. The only open-ended cases are glue-down floors over a non-porous substrate, where Mohawk asks for at least five days and Forbo says "additional time may be necessary because the adhesive may take longer to dry and cure."

Two answers circulate, and both come from real documents

The short answer people repeat is 24 hours. The long one is five days. Both are on maker paperwork, but they are usually answers to different questions.

The 24 hour figure is usually the foot traffic time. Mohawk lets people walk on glue-down LVT 24 hours after installation with its M95.0 adhesive, and asks you to wait 48 hours before wet cleaning and scrubbing. Milliken allows foot traffic after 12 to 24 hours and rolling traffic after 24 to 48 hours, then asks you to wait five days before the first clean. A crew that hears "you can use the floor tomorrow" and takes the scrubber out is using the wrong line of the sheet. Among the documents we read, only Gerflor's Tarasafe sheet sets 24 hours for cleaning, and it is a safety floor document from 2010.

Armstrong changed its own number. The 2011 Armstrong commercial guide gave four days for VCT, luxury vinyl, sheet vinyl and linoleum. The current AHF sheet for Armstrong Excelon VCT, which names Imperial Texture and Stonetex as the 2011 guide did, says five days. Both PDFs are still online, which is why both figures turn up. The newer sheet is the one to follow, and our VCT guide covers the finish program that starts once the wait is over.

The scrubber is a rolling load too

Armstrong says new VCT "should not be exposed to rolling load traffic for at least 72 hours after installation to allow the adhesive to dry." Mohawk restricts "heavy traffic, rolling loads, or furniture placement" for 72 hours on M95.0 glue-down LVT. Neither document names a floor scrubber, but a scrubber rolls on wheels and is heavy: our floor scrubber weight table puts a 28 in Tennant T500 at 620 lb with batteries and 810 lb with a full solution tank, and a T16 rider at 2,800 lb gross. We read the rolling load limits as applying to the machine itself, dry or wet. So do not drive a scrubber across a new floor to reach another area before the rolling load time is up, even with the brushes and water off.

A five-day rule for when you do not know the maker

On a job where the flooring maker or adhesive is unknown, use this:

  1. Glued floor, porous substrate, maker unknown: wait five days before any wet cleaning or machine scrubbing. That meets or exceeds every fixed figure in the table.
  2. Glued floor over a non-porous substrate: wait at least five days, and ask the flooring maker before scrubbing. Mohawk and Forbo both say this case can take longer.
  3. Floating or loose lay floor: no adhesive wait. Mohawk says cleaning "may begin immediately"; Altro leaves loose lay floors out of its 72 hours. The water limits in our LVT and vinyl guide still apply, because click joints let water through.
  4. Maker known: follow its figure, and its rolling load time if that is longer than you expected.

Until then, dry soil removal is what every document allows. Sweep, dust mop or vacuum. Armstrong and Milliken both name denatured alcohol on a clean white cloth for dried adhesive residue on the surface, and Milliken says not to pour water or alcohol directly on the floor.

The first scrub: what each maker allows

When the wait is over, the first machine scrub is where most of the settings below come from. These are the machine, pad and speed rules each document gives for initial or early cleaning.

MakerMachinePad or brushSpeedCleaner
Armstrong VCT (current)Rotary machine or auto scrubber3M red for light scrub, blue for deep; no brown or black pads, no stiff-bristled brushes300 rpm or lessDiluted cleaner such as S-485; "Do not flood the floor"
Milliken LVT"Auto Scrubber Machine: Rotary with 175 rpm Maximum"White, light green or red 3M pads; no dark green, black or brown175 rpmNeutral; never above pH 11
Interface LVTCounter-rotating dual cylindrical brush machine for heavy soil at the initial clean; auto scrubber in restorative maintenanceWhite or "soft" brush; red or white 3M pad on the auto scrubberNot statedNeutral, pH 6.0 to 9.0
Mohawk LVTRotary machine or auto scrubberBrush equivalent to a 3M red pad; never brown or black pads300 rpm or less for strippingpH-neutral
Altro Lavencia LVTAuto scrubber; low speed swing machineWhite, fine nylon pads on the scrubber; Altro UniPad on the swing machine150 to 350 rpm (swing machine)AltroClean 44 at 1:40, up to 1:10 for heavy soil; "DO NOT FLOOD THE FLOOR"
Forbo SafestepScrubber drier, rotary machine or cylindrical brush machineSuitable brush150 to 180 rpm (rotary)Neutral
Tarkett SafetredContra-rotating cylindrical, rotary scrubber or standard speed scrubber-dryerMedium brushStandard speedNeutral, pH 7, such as Carefree Stride 1000
Gerflor TarasafeHand or machine scrubStiff nylon bristle brushNot statedNeutral, in clean hot water, then a cold rinse

Two things stand out. Milliken is the strictest on speed, at 175 rpm. That rules out every cylindrical and orbital head, which turn at 600 rpm and up (see disc vs cylindrical), and it is tighter than most disc decks too: of the disc scrubbers in our asbestos floor tile speed table, only the Nilfisk SC500 at 155 rpm is under it, while the Kärcher and Minuteman discs run 180 and the Tennant T500 220. And Interface does not start new LVT on an auto scrubber at all: its initial maintenance is a damp microfiber mop with neutral cleaner, with a soft cylindrical brush machine only "if floor appears to be heavily soiled." The auto scrubber appears in its restorative maintenance, done "as needed or a minimum of once every 3 months."

On new VCT, Armstrong lists damp mopping and "at least two coats of a high-quality commercial floor polish" to "temporarily protect the floor until regular maintenance procedures can begin." The machine scrub comes after, under "Preparation for Commercial Traffic." For safety vinyl, our safety flooring guide covers the brush and chemical rules in more depth, and for linoleum the linoleum guide covers Forbo's and Armstrong's pH limits.

The longer rule: no aggressive stripper for two years

The adhesive wait is not the only time limit. Armstrong's current VCT sheet, and its 2011 guide for VCT and luxury vinyl, say: "The use of aggressive strippers such as mop-on/mop-off, no-scrub and no-rinse strippers is not recommended on tile floors less than two years old because they may affect the adhesive bond." If a new VCT floor needs its finish taken off in its first two years, use a conventional stripper with the method in our stripping guide, scrubbed at 300 rpm or less as Armstrong specifies.

Where this answer stops applying

  • Adhesive instructions. Several documents tie the wait to a named adhesive (Mohawk M95.0 and MS160). A different adhesive can have a different cure time; the flooring maker's installation instructions for that adhesive decide it.
  • Non-porous substrates. Mohawk and Forbo both say a glue-down floor over a non-porous substrate can take longer than their normal figure. Neither gives an upper limit.
  • Older documents. Gerflor's Tarasafe sheet is from 2010, Tarkett's Safetred sheet from 2012 and Forbo's US Marmoleum guide from 2013. Ask for the current version when the floor is under warranty.
  • Floor finish. This page is about the floor and its adhesive. The cure time of a freshly applied acrylic finish is a separate wait, set by the finish label.
  • New tile. Grouted tile has its own clock, and it is set by the grout, not by an adhesive. Our guide to removing grout haze gives the cure wait before any acid cleaner goes on.

Frequently asked questions

How long after installing LVT can you scrub it?

Two to five days for glue-down LVT in the documents we read: 48 hours for Mohawk and Interface, about 72 hours for Altro, and five days for Milliken. Floating LVT can be cleaned immediately, according to Mohawk.

How long before you can scrub new VCT?

At least five days for Armstrong VCT, according to the current AHF sheet, and keep rolling loads off it for 72 hours. Armstrong's older 2011 guide said four days.

Can you mop a new vinyl floor before the wait is over?

Sweeping, dust mopping and vacuuming are allowed in every document. Wet cleaning waits for the same time as scrubbing in most of them; Forbo, Tarkett and Gerflor apply their wait to any wet or any cleaning, not only to machines.

Why does the adhesive matter if the floor is waterproof?

Water gets in at the seams and edges. Armstrong says excess moisture "can interfere with the adhesive and/or seam treatments," and Milliken says it "can migrate between flooring seams and contribute to adhesive failure."

Sources

  • Armstrong Flooring (AHF), Vinyl Composition Tile (VCT) Maintenance Instructions (Print# 7440F10737-926): armstrongflooring.com
  • Armstrong, Maintenance Recommendations and Procedures for Commercial Resilient Flooring (F-8663-111, 2011), Home Depot document library: homedepot-static.com
  • Interface, Luxury Vinyl Tile Maintenance Guidelines (Rev. 12/15/2023): interface.com
  • Mohawk Group, Floating and Glue Down Luxury Vinyl Tile Maintenance (2017), copy hosted by Onni: onni.com
  • Milliken, LVT Initial Post Installation Maintenance Guide (05/2020): contenthub.milliken.com
  • Altro, Cleaning guide for LVT floors, Altro Lavencia LVT: altro.com
  • Altro, Cleaning guide for safety and slip-resistant floors (US, 2023): altro.com
  • Forbo Flooring, Floor Care: Safestep R11, Safestep R12, Safestep Aqua, copy hosted by Saltash Town Council: saltash.gov.uk
  • Forbo Flooring Systems, Floor Care Guidelines for Forbo Marmoleum Sheet and Tile with Topshield2 (v2.20, 10/13), copy hosted by a Forbo retailer: greengoodsusa.com
  • Tarkett, Safetred maintenance instructions (March 2012), via EBOSS: eboss.co.nz
  • Gerflor, Tarasafe ranges maintenance (May 2010), via SpecifiedBy: specifiedby.com