Can You Strip or Scrub Asbestos Floor Tile With an Auto Scrubber?
Can you scrub or strip asbestos vinyl or asphalt floor tile with an auto scrubber? OSHA's flooring care rules (300 rpm, wet methods, no sanding) set against the brush speeds of disc, cylindrical and orbital heads from Tennant, Nilfisk, Kärcher and Minuteman.
Key takeaways
- Yes, with a disc deck. OSHA allows stripping of asbestos-containing vinyl and asphalt flooring "using low abrasion pads at speeds lower than 300 rpm and wet methods." Every disc head in our table runs 155 to 285 rpm.
- Cylindrical and orbital heads are over the line. The spec sheets we read print 600 to 1,500 rpm for cylindrical brushes and 2,200 to 2,250 for orbital heads. OSHA says passing air monitoring at higher speeds is "not a sufficient condition" for a variance.
- Sanding is banned outright, and burnishing or dry buffing is allowed only where there is enough finish "so that the pad cannot contact" the tile. Worn traffic lanes fail that test.
- The regulation presumes asphalt and vinyl flooring installed "no later than 1980" contains asbestos, which includes 1980 itself. OSHA's fact sheet says "prior to 1980"; go by the regulation.
- The 175 rpm figure that also circulates is from OSHA's settlement on removing asbestos mastic after the tile is gone. It is not the maintenance limit.
Yes, with a disc scrub deck, a low abrasion pad and solution on the floor, and never by sanding. OSHA's construction asbestos standard says: "Stripping of finishes shall be conducted using low abrasion pads at speeds lower than 300 rpm and wet methods" (29 CFR 1926.1101(l)(3)(iii)), and the general industry standard that covers janitorial work repeats it word for word (1910.1001(k)(7)(ii)). A disc auto scrubber meets the speed limit with room to spare: the disc heads we checked turn at 155 to 285 rpm. Cylindrical and orbital heads do not. Their spec sheets print 600 to 2,250.
Two answers circulate. One says never put a machine on asbestos tile; the other says asbestos tile is safe as long as it is intact. Neither is what the rules say. EPA's answer to a parent who saw a janitor machine-cleaning school floor tile was that "machine-cleaning of floor tile can be part of a good maintenance program for asbestos-containing floor tiles, as long as the machine is operated properly and the tiles are not in poor condition." OSHA defines "operated properly" in numbers: under 300 rpm, a low abrasion pad, wet methods, no sanding, and burnishing only over intact finish. The machine is allowed. The machine's speed, pad and the condition of the finish are what is regulated.
Brush speeds against the 300 rpm line
OSHA's limit is written in revolutions per minute, so the scrub head type decides the answer before anything else does. We copied the brush or pad speed from each manufacturer's specification sheet.
| Machine | Scrub head | Brush or pad speed (spec sheet) | Under 300 rpm? |
|---|---|---|---|
| Nilfisk SC500 (53 B) | 530 mm (21 in) disc | 155 rpm | Yes |
| Kärcher BD 50/50 C Classic Bp | 510 mm (20 in) disc | 180 rpm | Yes |
| Minuteman E17 and E20 | 17 in and 20 in single disc | 180 rpm | Yes |
| Minuteman E26 and E30 | 26 in and 30 in, two discs | 180 rpm | Yes |
| Tennant T500 | 26, 28 and 32 in, two discs | 220 rpm | Yes |
| Tennant T300 | 17 in and 20 in single disc | 230 rpm (one figure printed across both columns) | Yes |
| Tennant T300 | 24 in, two discs | 285 rpm | Yes, by 15 rpm |
| Minuteman E20 | 20 in cylindrical | 600 rpm | No |
| Kärcher BR 40/10 C Adv (120 V) | 400 mm (16 in) roller brushes | 650 rpm | No |
| Minuteman E24 and E28 | 24 in and 28 in cylindrical | 850 rpm | No |
| Tennant T500 | 28 in cylindrical | 1,500 rpm | No |
| Tennant T300 | 20 in orbital | 2,200 rpm | No |
| Tennant T500 | 28 in orbital | 2,200 rpm | No |
| Nilfisk SC500 REV | 508 mm (20 in) orbital | "2250 orbital/30 pad" | No (see below) |
Every disc head clears the line and every other head type misses it by at least double. The T300's 24 in dual-disc head is the one to watch: at 285 rpm it is legal, with the least margin of any disc head we found. Check the sheet for the exact head on your machine, because the same model name can be sold with disc, cylindrical and orbital heads, and Minuteman's own sheets print 600 rpm for the E20 cylindrical and 850 rpm for the larger E24 and E28. See disc vs cylindrical for why roller brushes have to spin so much faster to do the same work.
The orbital case
Nilfisk's sheet for the SC500 REV prints "2250 orbital/30 pad" in its brush speed row, which shows the trap. An orbital head moves the pad in small, fast orbits and lets it creep round slowly, so the pad itself may turn at 30 rpm while the abrasive surface is scrubbing 2,250 times a minute. None of the OSHA documents we read addresses orbital motion; they speak only of rpm. We treat an orbital head as over the line for stripping asbestos flooring. The orbital scrubbers guide explains why these heads are sold for chemical-free stripping, which is exactly the work the rule restricts.
What OSHA's flooring rules say, line by line
Both asbestos standards carry the same care rules for flooring. OSHA's 1999 letter to RFM Inc. confirmed it: "Both standards contain the same requirements for care of asbestos-containing flooring material."
| Rule | Construction, 1926.1101(l)(3) | General industry, 1910.1001(k)(7) |
|---|---|---|
| Which floors | "All vinyl and asphalt flooring material," unless the building owner shows it contains no asbestos | Asbestos-containing flooring; asphalt and vinyl installed "no later than 1980" must be treated as asbestos-containing ((j)(1)) |
| Sanding | "Sanding of flooring material is prohibited" | "Sanding of asbestos-containing floor material is prohibited" |
| Stripping finish | Low abrasion pads, under 300 rpm, wet methods | Same wording |
| Burnishing or dry buffing | Only where the floor has "sufficient finish so that the pad cannot contact the flooring material" | Same, for asbestos-containing flooring |
Three details matter more than they look.
The construction rule has no date. Paragraph (l)(3)(i) applies to all vinyl and asphalt flooring, whatever its age, unless the building or facility owner demonstrates it is asbestos-free under (g)(8)(i)(I), which requires an industrial hygienist's determination "using recognized analytical techniques." A contractor stripping a 1995 floor under the construction standard is covered until someone has that determination in hand.
1980 is inside the presumption. The regulations say "no later than 1980." OSHA's fact sheet FS-3693 (11/2013) says flooring "installed prior to 1980 should be presumed to contain asbestos." The regulation is the binding text, so a floor laid in 1980 is presumed to contain asbestos.
The presumption is rebutted by a lab, not by looks. The fact sheet says the presumption holds "unless a piece of the material is sent to a reputable laboratory and analyzed for asbestos by transmission electron microscopy and found to contain a concentration of less than 1.0%." Our VCT guide covers the finish program on tile that has been cleared.
Faster machines need a variance, even with clean air samples
The obvious objection is that a faster machine is fine if the air sampling shows no exposure. OSHA rejected that in 1999. RFM Inc. asked whether negative exposure assessment data at higher speeds would justify a variance, and OSHA answered that "the fact that the asbestos PELs are not exceeded when the floor stripping uses low abrasion pads at speeds greater than 300 revolutions per minute (rpm) is not a sufficient condition to warrant the receipt of a variance." To get one, the employer must keep breathing zone levels "equal to or less than the levels occurring at speeds lower than 300 rpm." The same letter adds that "the Construction Asbestos Standard does not allow the use of alternative procedures for care of asbestos-containing flooring material," and that under either standard an employer who wants a different stripping or buffing method "must seek a permanent variance."
In practice that means a cylindrical or orbital scrubber is not a stripping machine for asbestos flooring unless your employer holds a permanent variance that names it.
The 175 rpm figure is for mastic, not for floor care
Search results also quote 175 rpm and a black pad. That comes from OSHA's 2005 letter on removing asbestos-containing mastic, the black cutback adhesive left on concrete after the tiles are up. Under OSHA's settlement with the floor covering industry, "the floor machine must be a low-speed floor machine that spins the floor pads at no greater than 175 revolutions per minute," and the adhesive is removed "using a floor machine equipped with a 3M black floor pad (or equivalent)." The Resilient Floor Covering Institute's Recommended Work Practices (January 2018) print the same black pad method for cutback adhesive.
That is removal work, a different job from maintaining a floor that stays in place. For stripping and refinishing tile in service, the line is 300 rpm. Do not put a black pad on intact asbestos tile because the mastic procedure names one.
Which jobs a disc auto scrubber can do on asbestos tile
- Routine scrubbing of intact finish: yes. EPA calls machine cleaning part of a good maintenance program when tiles are not in poor condition. Use a disc head, the pad you use on finished VCT, and solution down. OSHA's fact sheet lists "operate buffers only at speeds lower than 300 rpm" and "use wet methods" among the training points for flooring care, so keep the cylindrical machine off these floors even for daily work.
- Top scrub and recoat: yes, the same as stripping in miniature. Disc head, low abrasion pad, solution on the floor, and stop while finish remains.
- Full strip: yes, with a disc head under 300 rpm, a low abrasion pad, stripper kept wet, and the recovery done by the scrubber. OSHA does not define "low abrasion" or name a pad color for this work; take the pad from your asbestos program or the pad maker in writing. Our stripping guide covers dilution, dwell and the squeegee-up first pass. RFCI says the same about floors that will be covered over: "Remove wax and other finishes by wet stripping only."
- Burnishing: only over enough finish that the pad never reaches tile. A burnisher spins at 1,500 to 3,000 rpm (see scrubber vs burnisher), so on a worn traffic lane it is dry buffing bare asbestos tile. Recoat first.
- Anything that sands, grinds or scarifies: no. Sanding is banned in both standards, and RFCI adds dry sweeping, dry scraping, drilling, sawing, bead blasting and mechanical chipping to its "do not" list.
Where this answer stops applying
- Tile in poor condition. EPA's yes is conditional on tiles "not in poor condition." Broken, curling or powdering tile is a repair or abatement job for an asbestos program, not a scrubber job.
- Removal and renovation. Taking tile up is asbestos removal under 1926.1101(g)(8), with its own work practices: intact removal, wet scraping, no rip-up of sheet flooring. A floor scrubber has no role in it beyond the procedures your abatement contractor approves.
- Floods and water damage. Our flood water guide notes that one university sends areas with potential asbestos exposure to a specialized team rather than to custodial crews.
- Schools. EPA's answer pointed schools to its special guidance on asbestos floor tile maintenance through the TSCA Hotline; we could not retrieve that guidance, so it is not summarized here. Our schools guide covers the scrubber side.
- Other countries and states. This page covers U.S. federal OSHA. A state plan or an asbestos program written for your building can be stricter.
Frequently asked questions
What rpm is allowed to strip asbestos floor tile?
Lower than 300 rpm, with low abrasion pads and wet methods, under both 1926.1101(l)(3)(iii) and 1910.1001(k)(7)(ii). Disc scrub decks typically run 155 to 285 rpm on the sheets we checked.
Can you use an orbital scrubber on asbestos tile?
Not to strip it without a permanent variance. Orbital heads are rated at 2,200 to 2,250 per minute, and OSHA's 1999 letter says higher speeds need a variance even when exposure limits are not exceeded.
Can you burnish asbestos floor tile?
Only where the finish is thick enough that the pad cannot touch the tile. On worn lanes where finish is gone, recoat before burnishing.
How do you know if floor tile has asbestos?
You do not, by looking. Treat asphalt and vinyl flooring installed in 1980 or earlier as asbestos-containing unless a lab analysis by transmission electron microscopy finds less than 1.0 percent, as OSHA's fact sheet describes.
Sources
- 29 CFR 1926.1101, Asbestos (construction), paragraphs (b), (g)(8), (k)(1) and (l)(3), via eCFR: ecfr.gov
- 29 CFR 1910.1001, Asbestos (general industry), paragraphs (b), (j)(1) and (k)(7): osha.gov
- OSHA standard interpretation, Questions regarding the cleaning of asbestos-containing floor tile (November 5, 1999), letter to RFM Inc.: osha.gov
- OSHA standard interpretation, Prohibitions and/or restrictions on aggressive methods for removing asbestos-containing mastic from floors (May 18, 2005): osha.gov
- OSHA Fact Sheet FS-3693, Protecting Workers from the Hazards of Asbestos-Containing Flooring Material Maintenance (11/2013): osha.gov
- U.S. EPA, I have seen the janitor machine-cleaning the floor tile in our school (archived January 19, 2021 snapshot): epa.gov
- Resilient Floor Covering Institute, Recommended Work Practices for Removal of Resilient Floor Coverings (January 2018): rfci.com
- Tennant, T300 specifications, North America (Rev 10-23): tennantco.com
- Tennant, T500 specifications, North America (Rev 10-23): tennantco.com
- Nilfisk, SC500 brochure (Spanish edition): nilfisk.com
- Kärcher, BD 50/50 C Classic Bp product information (1.127-001.0): kaercher-media.com
- Kärcher, BR 40/10 C Adv product information (1.783-312.0, Canada): kaercher-media.com
- Minuteman, E20 disc and cylindrical specifications, via WebstaurantStore: webstaurantstore.com
- Minuteman, E Series specifications (E17 to E30), via WebstaurantStore: webstaurantstore.com