How Do You Clean an ESD Floor With an Auto Scrubber Without Ruining Its Resistance?
How to clean an ESD static dissipative or conductive floor with an auto scrubber without raising its resistance: cleaner, pad, finish and rinse rules from ACL, Legge, Statguard, KLB, Polyflor, Forbo, Tarkett and Altro.
Key takeaways
- Scrub with a cleaner that has no care components and leaves no film, recover all of it, and measure resistance afterwards. Residue, not pH, is what pushes an ESD floor out of spec.
- KLB allows neutral to slightly alkaline machine cleaners up to pH 10.5 on its conductive resin floors, provided they contain "no care components" and "do not leave a residue." A pH 7 cleaner that leaves a film is the worse choice.
- Keep polish and wax off ESD floors unless the floor maker approves the product and you test it: Tarkett says wax or polish "may change the products conductive behaviour," and Altro says polishes "may affect the static dissipative properties."
- Pads: red at most for routine scrubbing on KLB resin and Statguard tile, blue only for basic cleaning. Statguard's own automatic scrubber method fills the tank with its floor stripper and ends with its neutralizer to bring the floor back to pH 7.0.
- ACL's 1,500 to 2,000 rpm figure for scrubbing with Staticide 4100 is a burnisher speed. A disc scrubber cannot run it; take the light pressure and the resistance check from that instruction instead.
Scrub with a cleaner that contains no care components and dries without a film, pick all of it up, and measure resistance when you finish. KLB's guide for its conductive resin floors puts the rule plainly: "It is important to use cleaning products that do not leave a residue on the floor and dry well so as not to impair conductivity." The auto scrubber itself is not the risk. KLB names an "automatic scrubber dryer" for routine maintenance cleaning, Statguard names an "Automatic Scrubber" for its ESD vinyl tile, and ACL sells a cleaner for ESD finishes that is "suitable for mops, auto-scrubbers, and standard burnishing machines."
The confusion behind the question is the word neutral. Floor care advice says to use a neutral cleaner, and ESD floor makers say the same: Altro asks for "a neutral cleaner" on Altro Walkway 20SD, and Tarkett uses a neutral detergent on its SD and conductive linoleum. But ESD cleaner makers warn that ordinary cleaners are the problem. Legge's Stat-Les data sheet says "many cleaners leave behind a film that will also insulate a static dissipative or conductive surface," and ACL says "Cleaners that are safe for most floor polishes can often harm ESD finishes by introducing contaminants." Both are right, about different things: pH protects the floor material, while resistance depends on what is left on top of it. KLB settles it by allowing cleaners well above neutral, up to pH 10.5, as long as they carry no care components and leave no residue.
What ESD floor and cleaner makers say: nine documents
We read the care documents for ESD floor coverings and cleaners and copied the machine, chemical, pad, finish and testing rules as written.
| Document | Floor | Machine named | Cleaner | Pad or brush | Polish, finish or dressing | Rinse and test |
|---|---|---|---|---|---|---|
| KLB Kötztal, cleaning recommendations for conductive commercial and industrial flooring (05/2022) | Conductive and ESD reactive resin coatings | "Automatic scrubber dryer" | Neutral to slightly alkaline, pH 10.5 or less, "without any care components" | Super pad up to red; soft to medium-hard brush (e.g. polyester). Basic cleaning: up to blue | Care dispersions allowed after checking with the maker; test areas | Clear water after basic cleaning; measure discharge resistance after basic cleaning and after coating |
| Statguard, 8400 Series ESD vinyl floor tile maintenance (TB-5032, December 2024) | ESD vinyl tile | "Automatic Scrubber" or low-speed swing buffer | Scrubber: Statguard Floor Stripper in the tank. Swing buffer: Statguard ESD Floor Cleaner | Normal: red. Heavy: blue, green, or brown with stripper applied liberally | Not addressed; buff dry with a red pad on a low-speed swing buffer | Statguard Floor Neutralizer "to bring the pH level down to level 7.0" |
| ACL, Staticide 4100 Restorer Cleaner data sheet | Staticide dissipative floor finishes, ESD tiles | Mop, auto scrubber, burnisher | 10:1 (water to concentrate); no ammonia, phosphates, alkali or acids | "Clean polishing pad," light pressure | The finish is the ESD layer: 4100 helps maintain "10e7 – 10e9 ohms" | "Check resistance readings and apply a second treatment if necessary" |
| Legge, Stat-Les Cleaner K4050 data sheet | Conductive and static dissipative floors, finishes, mats | Not addressed | pH 7.6; 2 to 4 oz per gallon general, up to 32 oz heavy soil | Not addressed | Not addressed | "No rinsing is required" |
| objectflor, Polyflor ESD vinyl maintenance (07/2026): Finesse EC, Finesse SD, Palettone SD, Polyflor SD | ESD vinyl | Not addressed (damp mop; rotary for spray cleaning) | Floor maintainer, mopped twice "to remove any residue"; alkaline for build-up | Soft pad, "white, max. red" | Dressings only after a test area shows they do not impair ESD properties | Initial clean rinsed "until a neutral pH value is restored" |
| Forbo, linoleum cleaning and maintenance advice | Marmoleum Ohmex (conductive) | Rotary machine or scrubber drier (all linoleum) | Only products "that do not reduce the conductivity of the flooring" | Red (all linoleum) | Same rule | Not addressed |
| Tarkett, Linoleum xf2 care recommendation (February 2017) | Linoleum xf2 SD and Conductive | "Combined machine (for large areas)" | Diluted neutral detergent | Red or brown pads; low speed, 150 to 250 rpm "or higher" | "Do not treat the flooring with wax or polish!" | Not addressed |
| Altro, APAC cleaning guide for safety flooring (January 2023) | Altro Walkway 20SD | Rotary cleaning machine (all Altro safety floors) | Neutral cleaner | Altro UniPad or medium pads (all Altro safety floors) | "Aggressive cleaning or the use of polishes may affect the static dissipative properties" | Not addressed |
| ANSI/ESD S20.20-2021 flooring limit, as summarized by OCSiAl (TUBALL) | All ESD flooring | Not addressed | Not addressed | Not addressed | Not addressed | Flooring resistance under 1 x 10⁹ ohms at all points |
The documents agree on two things: no film the floor maker has not tested, and a resistance check afterwards rather than trust in the label.
Why "use a neutral cleaner" is not enough
An ESD floor sheds charge through a conductive path in or on its surface. KLB explains that conductive pigments or fibres are built into its coatings, and that "dirt usually has an insulating effect and therefore impairs conductivity." Legge says the same about soil: "dirt insulates your surface." So two kinds of layer push resistance up: soil the scrubber did not remove, and film the cleaning left behind.
pH tells you neither. A neutral cleaner-maintainer sold to leave a protective sheen still lays down a film. That is why KLB's limit has two parts, pH 10.5 or less and "without any care components," and why objectflor tells crews to mop the Polyflor ESD maintainer on, wring out, and go over it again "to remove any residue." Our neutral cleaners guide explains why neutral is the daily default on most floors. On an ESD floor, neutral is the starting point and residue-free is the requirement.
The other half of the confusion is the dedicated ESD cleaner. Legge's Stat-Les and ACL's Staticide 4100 are not just neutral; both are formulated to sit on the floor. Legge says Stat-Les will "enhance the surface resistivity readings" with "no rinsing" required, and ACL says 4100 "contains special conductive additives." That residue was designed to be conductive. Do not generalize from it to an ordinary cleaner, and do not mix the two in one tank.
Choose by floor type
- Conductive or ESD resin coating (epoxy or polyurethane): KLB's rules. Neutral to slightly alkaline cleaner, pH 10.5 or less, no care components, red pad maximum or a soft to medium-hard brush. Our epoxy floors guide covers the resin itself.
- ESD vinyl tile (Statguard 8400): red pad for normal cleaning. Statguard's scrubber method runs its stripper in the tank and finishes with its neutralizer to pH 7.0; on that floor, follow Statguard's chemicals rather than a general-purpose cleaner.
- ESD vinyl sheet and tile (Polyflor via objectflor): objectflor gives no scrubber method. A scrubber run should match its limits: white or red pad, a residue-free cleaner, alkaline only for build-up.
- Conductive or SD linoleum (Forbo Ohmex, Tarkett xf2 SD and Conductive): the general linoleum rules apply, neutral detergent and a red pad (Tarkett also allows brown), plus no wax or polish on Tarkett and only conductivity-safe products on Ohmex.
- Static dissipative safety vinyl (Altro Walkway 20SD): neutral cleaner, no polish, and nothing aggressive. Our safety flooring guide covers the pads Altro allows.
- A floor whose ESD property comes from a dissipative finish: here the finish is the conductive layer, so the risk is scrubbing it off. ACL's instruction is a clean polishing pad, light pressure, its 4100 cleaner at 10:1, and a resistance check.
The ACL 1,500 to 2,000 rpm figure
ACL's 4100 data sheet says: "For auto scrubbers, gently scrub using diluted solution and clean polishing pad. Use 1500 - 2000 RPM with a light pressure setting to prevent removal of finish." That speed belongs to a burnisher. A disc scrubber turns at roughly 150 to 300 rpm, and a burnisher at roughly 1,500 to 3,000 (see scrubber vs burnisher), so ACL's figure is about ten times what a disc scrubber deck runs. A burnisher, for its part, spins a pad dry and does not recover water.
The sentence is protecting the finish. The usable parts are the light pressure setting, a polishing pad rather than a scrub pad, and the resistance check that follows. The rpm figure fits the "standard burnishing machines" the same sheet lists.
Finish, polish and dressing
The documents run from a flat no to a conditional yes:
- No: Tarkett on xf2 SD and Conductive ("Do not treat the flooring with wax or polish!"). Altro on Walkway 20SD says polish "may affect" the static dissipative properties.
- Only what does not reduce conductivity: Forbo on Ohmex; objectflor, which says ESD floor coverings "must not be treated with maintenance products that could impair the conductibility."
- Yes, after testing: KLB says modern care dispersions for conductive floors can meet DIN EN 61340-4-1 and/or DIN EN 1081, and asks for the discharge resistance to be checked "after finishing, ideally after each intermediate coat." objectflor wants a sample area tested for "sufficient conductivity" before any polymer dispersion.
- The finish is the ESD layer: ACL's Staticide dissipative finishes, maintained at 10⁷ to 10⁹ ohms (ACL prints it "10e7 – 10e9").
How to auto scrub an ESD floor
These steps combine what the documents share. Use the floor maker's own cleaner list where it has one.
- Dry soil first. Every document starts with sweeping, vacuuming or a dust mop. KLB adds dirt trap mats at entrances, and only mats "without plasticiser content."
- Mix the cleaner at label dilution. KLB: "Both over- and under-dosing lead to undesirable cleaning results." Over-dosing is residue.
- Fit a red pad or softer, or a soft to medium-hard brush. Blue, green and brown are for basic or heavy cleaning only, and only where the maker lists them.
- Scrub and recover in one pass for routine cleaning. For intermediate cleaning, KLB lays the solution down without suction, waits about 5 to 10 minutes, then makes a second pass to pick it up.
- Rinse with clear water after anything stronger than routine. KLB rinses after basic cleaning "as alkaline basic cleaners require thorough neutralisation"; Statguard neutralizes to pH 7.0. Our residue and rinsing guide covers how many passes it takes.
- Let it dry, then measure resistance in the traffic lanes. ANSI/ESD S20.20-2021 sets flooring under 1 x 10⁹ ohms at all points; a reading drifting toward that line after cleaning points at residue.
Our manufacturing plants guide covers scrubber setup for light-soil electronics and assembly areas.
Disinfectants on ESD floors
KLB is the only document here that addresses them. Surface disinfectants on dissipative floors should "not contain any care components and dry up without leaving a residue," pH 10.5 or less. If one does leave residue, KLB says to clean the area with clear water after the exposure time. See our disinfectant guide for why a scrubber pass alone rarely meets a label contact time.
Where this answer stops applying
- Explosive atmospheres. KLB lists Ex rooms among conductive floor uses. Whether a battery scrubber may enter one is a hazardous location question, not a floor care one.
- Floors not in these documents. Roppe, Mondo and other ESD makers publish their own care sheets; we could not retrieve them. Ask the floor maker, and test any new chemical on a small area with a resistance reading before and after.
- Your own resistance spec. The 1 x 10⁹ ohm figure is the S20.20 flooring limit. A program or floor specified to a tighter limit needs its own number.
Frequently asked questions
Can you use a regular neutral floor cleaner on an ESD floor?
Only one with no care components that dries without a film. KLB allows cleaners up to pH 10.5 on conductive floors on that condition, while Legge warns that many all-purpose cleaners leave a film that insulates the surface.
Do you need to rinse an ESD floor after scrubbing?
After basic or alkaline cleaning, yes: KLB rinses with clear water and Statguard neutralizes to pH 7.0. Legge's Stat-Les is the exception, designed to be left on with no rinse.
Can you wax or polish an ESD floor?
Not with ordinary floor finish. Tarkett bans wax and polish on its SD and conductive linoleum, and KLB and objectflor allow a care dispersion only after testing its effect on resistance.
What pad should you use on an ESD floor?
Red or softer for routine scrubbing. KLB allows up to red for maintenance and up to blue for basic cleaning; Statguard uses red for normal cleaning and blue, green or brown for heavy cleaning with its stripper.
Sources
- KLB Kötztal Lacke + Beschichtungen, Cleaning and maintenance recommendations, electrically/ESD-conductive commercial and industrial flooring (Edition 05/2022): klb-koetztal.de
- Statguard Flooring (Desco Industries), Technical Bulletin TB-5032, 8400 Series ESD Vinyl Floor Tile Maintenance (December 2024), via TestEquity: testequity.com
- ACL Inc., Staticide 4100 Restorer Cleaner technical data sheet: aclstaticide.com
- Walter G. Legge Co., Stat-Les Cleaner K4050 technical data sheet, via TestEquity: testequity.com
- objectflor, Maintenance instruction, Polyflor ESD vinyl flooring (07/2026): objectflor.de
- Forbo, Cleaning and Maintenance advice (linoleum floorcare, general), copy hosted by a Forbo retailer: greengoodsusa.com
- Tarkett, Linoleum Floors Care Recommendation, Linoleum xf2 (February 2017): tarkett.com.br
- Altro, Recommended cleaning methods, Altro safety flooring (APAC, January 2023): altro.com
- OCSiAl TUBALL, Choosing between dissipative and conductive in ESD-control flooring: a review of ANSI/ESD S20.20-2021: tuball.com