Maintenance

Can You Pressure Wash a Floor Scrubber?

What 18 floor scrubber manuals say about pressure washing, hosing and steam, the IPX3 rating most machines carry, and which parts you can rinse with a hose.

Key takeaways

  • No. None of the 18 operator manuals we read allows a pressure washer on the machine's body, and 13 of them ban hosing or spraying the whole machine with water. Tennant's line is "do not power spray or hose off machine. Electrical malfunction may occur."
  • The rating explains why. Seven Tennant manuals print IPX3, which under IEC 60529 means spray up to 60 degrees from vertical, tested at 50 to 150 kPa. A Kärcher HD 5/15 C pressure washer works at 150 bar, 100 times the top of that test.
  • The exterior gets a damp cloth and mild or all purpose cleaner. Kärcher's BD 50/50 manual says "Do not sluice the appliance with water."
  • Water jets are allowed on parts: the inside of the tanks, a removed vacuum hose, the squeegee and the brush. Tennant's T1 manual has you flush the vacuum hose with a garden hose after covering the vacuum intake screen.
  • The exception is Tennant's M17 and M20 sweeper-scrubbers, which offer an onboard high pressure washer. Even there the M20 manual says not to get water on electronic components when using it to clean the machine.

No. None of the 18 floor scrubber operator manuals we read allows a pressure washer on the machine's body, and 13 of them forbid hosing or spraying the whole machine at all. Tennant's walk-behind manuals put it in one line: "do not power spray or hose off machine. Electrical malfunction may occur. Use damp cloth." Clean the outside with a damp cloth and a mild or all purpose cleaner. Rinse the tanks, hoses, squeegee and brush, which are built to get wet, and keep jets of water away from the controls, motors and batteries.

Two answers circulate. One says a scrubber spends its life in water, so hosing it down is fine. The other says no water should ever touch it. Both are wrong. The first persists because the parts you see are wet all shift: the tanks, the squeegee, the brush. But the motors and controls sit right next to them, and the machine is only rated for light spray. The second persists because the warnings are written broadly. The same manuals that ban hosing the machine tell you to spray water into the tanks and to flush the vacuum hose with a garden hose. The rule is about where the water goes, not whether you use any.

What 18 manuals say about pressure washing and hosing

We read the safety and maintenance sections of each manual and copied the washing rule as written.

Machine (manual)Washing rule, as writtenPrinted protection rating
Tennant T600 EE walk-behind (9016606 Rev. 01, 02-2023)"Do not power spray or hose off machine. Electrical malfunction may occur. Use damp cloth."IPX3
Tennant T260 walk-behind (TN7100012 Rev. 01, 01-2024)"Do not power spray or hose off machine." Do not use "high-pressure spray or water pipe to flush the machine, which may cause electrical system failure."Not printed
Tennant T5 walk-behind (9002326 Rev. 08, 10-2015)"Do not power spray or hose off machine."IPX3
Tennant T3/T3+ walk-behind (9004144 Rev. 03, 04-2010)"Do not power spray or hose off machine. Electrical malfunction may occur."IPX3
Tennant T1 battery walk-behind (9008591 Rev. 01, 07-2016)Same wording as the T3IPX3
Tennant T16 rider (9008142 Rev. 00, 1-2011)Spray nozzle option cleans the machine, but "DO NOT get water on electronic components." No steam in the tanks. "Do not wash the pads with a pressure washer."Not printed
Tennant T17 rider (9020160 Rev. 01, 1-2015)"Do not power spray or hose off machine near electrical components." No steam in the tanksIPX3
Tennant M17 battery sweeper-scrubber (4020655 Rev. 9, 2-2026)Same as the T17. Optional high pressure washer "for heavy duty cleaning"IPX3
Tennant M20 gas/LPG sweeper-scrubber (9016000 Rev. 06, 3-2024)Same as the T17. With the optional high pressure washer, "Do NOT get water on electronic components" when cleaning the machineIPX3
Nilfisk SC6000 rider (56091161 Rev. A, 4/2016)"Do not pressure wash operator control panel, circuit breaker panel or batteries."Not printed as IP
IPC CT15, CT30, CT45, CT46"Never wash the machine with water jets." Avoid high pressure washers: water "could penetrate the electrical compartment or motors." No steamNot printed
Minuteman E14 micro scrubber (988760 Rev. A, 04/22)"Never wash the machine with direct or pressurized jets of water or with corrosive substances"IP 22 battery, IP 23 cord
Betco Stealth DRS 26/32 riderSame sentence as the E14Not printed
Clarke CA30 20B walk-behind (56091130)"Do not wash the machine directly with water."Not printed
Viper AS430C walk-behindSame sentence as the CA30 20BNot printed
Trusted Clean Dura 17 walk-behind (04-2023)Same sentence as the CA30 20BNot printed
Kärcher BD 50/50 C Bp Classic (11/18)"Risk of damage. Do not sluice the appliance with water and do not use aggressive detergents."Not printed
Kärcher BD 35/15 C Classic Bp"Do not spray the device with water."Not printed

The Clarke, Viper and Dura manuals share one sentence, and the Minuteman and Betco manuals share another, so they are fewer independent voices than the row count suggests. They still agree with everyone else.

Three things stand out.

  • Walk-behinds get the strict rule. Every walk-behind and micro scrubber here bans hosing the whole machine, not just the electrical parts. Size has nothing to do with it: the T600 EE is a 2 kW machine, and its rule is the same as the T1's.
  • Riders get a qualified rule. Tennant's T16, T17, M17 and M20 manuals add "near electrical components," and the Nilfisk SC6000 names the parts to keep dry. That is not permission to pressure wash the rest. It means the manual expects water on the deck and frame and tells you which parts to keep it off.
  • Steam is out too. IPC bans steam because the heat can warp "plastic parts," and four Tennant rider manuals say "DO NOT use steam to clean the tanks."

Why a pressure washer beats the rating

The protection rating tells you how much water the enclosure was tested to take. Under IEC 60529, the second digit of an IP code is the water rating. Seven of the Tennant manuals print IPX3: the X means dust was not rated, and the 3 means "water sprayed at an angle up to 60° on either side of the vertical shall have no harmful effects." The Minuteman E14's IP 22 and IP 23 mean the battery model is rated one step lower than the cord model.

Water digitIEC 60529 descriptionTest water
2Drops falling vertically, enclosure tilted up to 15°Drip test
3Spray at up to 60° from vertical10 L/min at 50 to 150 kPa (7 to 22 psi)
4Splashing from any direction10 minutes, splash from all sides
5Jets from any direction6.3 mm nozzle, 12.5 L/min, 30 kPa at 3 m
6Powerful jets from any direction12.5 mm nozzle, 100 L/min, 100 kPa at 3 m
9Close-range high-pressure, high-temperature spray14 to 16 L/min, 80 to 100 bar, 80 °C (176 °F)

Now compare a pressure washer. Kärcher's HD 5/15 C, a common professional cold water unit, has a working pressure of 150 bar (15 MPa, about 2,175 psi). That is 100 times the top of the IPX3 spray test, and above even the 80 to 100 bar of the IPX9 close-range spray-down test. No manual we read rates a floor scrubber higher than IPX3, which is two steps short of the jet test at 5.

One more catch if you compare machines: the water digits are cumulative only up to 6. A product rated IPX7, for immersion, is not necessarily rated for jets at 5 or 6. Read the specification table at the back of your own manual rather than a brochure for a similar model.

What water does once it is inside

The manuals name the damage. Tennant says "electrical malfunction may occur," and the T260 manual says "electrical system failure." IPC names the "electrical compartment or motors" and "the risk of short circuit." Our drive motor guide lists pressure washing among the causes of water getting into drive motors, and our scrubber won't start guide notes that emergency stop contact blocks can fail open on pressure-washed machines. Water in a battery compartment is a separate problem. Tennant's M17 manual has you clean the battery tops "with a strong solution of baking soda and water" every 200 hours, by hand, with the battery caps left on. Our battery maintenance guide covers that job.

What you can rinse with water

The same manuals that ban hosing the machine send water through the parts that are built to be wet. These are the jobs the manuals describe:

  • Tank interiors. Kärcher's BD 50/50 manual says to rinse the waste water tank with clear water after each use. Tennant's T5 manual has you remove the clean-out cap and "spray water directly into the clean-out ports" of the solution tank. Our recovery tank odor guide has the full deep clean.
  • The vacuum hose. Tennant's T1 manual has you put a dry towel over the vacuum intake screen first, "to prevent water from entering vacuum motor," then run a garden hose into the vacuum hose. Turn the water on slowly, and flush both sides of its Y-shaped hose. Betco's Stealth manual removes the hose from the machine first and cleans the inside "with a powerful jet of water." More on hoses is in vacuum hoses and seals.
  • Squeegee and brush. The Minuteman E14 manual says to clean the squeegee "with a jet of clean water," and to remove the brush and clean it the same way.
  • Pads, by hand. Tennant's T16 manual says pads should be cleaned right after use "with soap and water" and hung or laid flat to dry, and "Do not wash the pads with a pressure washer." Our brushes and pads guide covers pad colors and care.

The pattern is clear: water goes into the tanks and through removable parts, never onto the body, the controls or the motor openings. The vacuum motor is the part most at risk. Tennant's T1 manual warns against splashing water on the vacuum motor intake screen even while you fill the solution tank: "Vacuum motor failure may result."

The one exception: an onboard pressure washer

Tennant sells an optional high pressure washer on its M17 and M20 rider sweeper-scrubbers. The manuals say it is "for heavy duty cleaning," it runs only with the parking brake set, and you must not put detergent in the solution tank when using it or "pressure washer damage could occur." The M20 manual expects it to be used on the machine itself, with one condition: "Do NOT get water on electronic components when using the high pressure washer to clean the machine." Both manuals still carry the safety line "Do not power spray or hose off machine near electrical components," and both rate the machine IPX3.

So even the one maker that fits a pressure washer to a scrubber treats the machine's electrics as off limits to it. If you need to wash down a large outdoor machine regularly, our sweeper-scrubber guide explains which models are built for dirty sites. For a walk-behind there is no such option.

How to clean the outside of a floor scrubber

  1. Turn it off and disconnect power. Tennant's T260 manual says to "disconnect battery cables and charger cord before cleaning and servicing machine." On a cord model, unplug it.
  2. Drain and rinse the tanks at a sanitary drain, as covered in where to dump floor scrubber water.
  3. Wipe the body with a damp cloth. Tennant asks for an all purpose cleaner, Kärcher for a cloth "soaked in mild detergent." Kärcher bans aggressive detergents, IPC bans hydrocarbons and solvents because they damage the cowling and rubber parts, and the E14 manual bans corrosive substances.
  4. Rinse the parts, not the machine. Squeegee, brush or pad, and the vacuum hose, as above. Remove them where you can, so the water runs into a sink and not over the scrub deck motors.
  5. Leave the recovery tank open to dry. It is the last step in our daily maintenance checklist for a reason.

Where this stops applying

  • Your manual comes first. We found no scrubber manual that allows a pressure washer on the whole machine, but we did not read every model. If yours prints a rating of IPX5 or higher and says so, follow it.
  • Outdoor work is a different question. A machine rated IPX3 also has limits on rain, which is why most manuals keep scrubbers indoors. Our guide to using a floor scrubber outside sets those out.
  • Food plants and wash-down areas. If a sanitation program requires equipment to be washed down, a standard scrubber does not meet that by its own ratings. Ask the dealer in writing for a model rated for the wash-down method you use.
  • Non-electric parts off the machine. Squeegee blades, disc brushes and pad drivers removed from the machine are just plastic, rubber and bristle. Tennant still bans the pressure washer on pads, so check the manual before pressure washing those too.

Frequently asked questions

Can I hose down my floor scrubber?

Not the whole machine. Tennant's walk-behind manuals and the Clarke, Kärcher, IPC and Minuteman manuals all forbid hosing, spraying or jetting the body. You can hose the inside of the tanks and a vacuum hose, as Tennant's T1 manual describes, after covering the vacuum intake screen.

What IP rating does a floor scrubber have?

Seven Tennant manuals we read print IPX3, which covers spray up to 60 degrees from vertical. The Minuteman E14 prints IP 22 for the battery model and IP 23 for the cord model. None of the 18 manuals prints IPX5 or higher.

Can you steam clean a floor scrubber?

No. IPC's manual bans steam because the heat can warp plastic parts, and Tennant's T16, T17, M17 and M20 manuals say not to use steam to clean the tanks.

Sources