How Do You Transport a Floor Scrubber in a Truck or Trailer?
How to load, block and strap a floor scrubber in a truck or trailer: steps from 11 operator manuals, tie-down points, and the federal tiedown count and strength rules.
Key takeaways
- Drain both tanks, raise the scrub head and squeegee to load, then lower them, block every wheel and strap the machine at the tie-down points its manual names. Seven of the 11 manuals we read ask for empty tanks, and none says to travel with water aboard.
- Riders have a loading rule walk-behinds lack. Tennant's T16 and T17 may be driven on only if the loading surface is level and 15 in (380 mm) or lower. Otherwise you winch them on by the stabilizer legs.
- The federal four-tiedown rule for machinery starts at 10,000 lb, and no scrubber in our table comes close. Under the general rule, a machine over 5 ft long needs at least two tiedowns, and their combined working load limit must reach half its weight.
- Use the manual's tie-down count anyway. The T600 EE walk-behind has four tie-down brackets, and the M20 and T17 riders strap at the front and at the rear jacking brackets.
- Never strap to the control console or accessory rails, and on an open trailer latch the tank lids and access doors.
To transport a floor scrubber, drain both tanks, raise the scrub head and squeegee, and load the machine with a dock, liftgate, winch or a ramp its manual allows. Then put the front against the front of the bed, lower the scrub head and squeegee, block each wheel, and strap the machine at the tie-down points its manual names, often four. On a machine over 5 ft long, use at least two tiedowns whose combined working load limit reaches half the machine's weight. That is the federal minimum. Tennant's T600 EE manual, for one, names four brackets.
Two answers circulate. One says a scrubber is just cargo, so a strap or two will do. The other says it is heavy equipment, so it needs four chains like a skid steer. The first comes close to the legal minimum on a small walk-behind but ignores the manual. The second borrows a rule that does not apply. The four-tiedown rule in 49 CFR 393.130 covers machinery that "individually weigh[s] 4,536 kg (10,000 lb.) or more," and the heaviest scrubber below is 4,770 lb with batteries. Below 10,000 lb the general rules apply, and those can be met with fewer straps. The manuals still ask for four, and the manual is the document you answer to if the machine is damaged.
What 11 operator manuals say about transporting a scrubber
We read the transporting section of each manual and copied the steps as written.
| Machine (manual) | Before loading | Loading rule | In transit |
|---|---|---|---|
| Tennant T600 EE walk-behind (9016606) | "Drain tanks, raise scrub head and remove scrub disks and squeegee assembly" | Ramp must hold machine and operator. Machine "may only be operated on gradients up to 2%" while loading | Front against the front of the bed, scrub head down, key off, block each wheel, strap at "the four tie-down brackets." Secure the recovery tank lid on an open truck |
| Tennant T5 walk-behind (9002326) | Drain tanks | Ramp that holds machine and person loading it | Front against the front of the bed, scrub head and squeegee down, parking brake if equipped, block each wheel, tie-down straps |
| Tennant T3/T3+ walk-behind (9004144) | Raise squeegee and scrub head | "Recommended loading ramp" | Front against the front of the bed, head and squeegee down, block each wheel, straps "over the top of machine to prevent it from tipping" |
| Tennant T260 walk-behind (TN7100012) | No transport procedure given | Do not "transport on inclines that exceed 21% grade" | Not stated |
| Betco GeneSys mid-size walk-behind (92501-92) | Remove the squeegee and stow it on the trailer | Up the ramp | Scrub deck down, straps across the front and rear of the battery compartment with the tank open |
| Tennant T16 rider (9008142) | Empty both tanks | Drive on only if the surface is horizontal and 380 mm (15 in) or lower, otherwise winch by the stabilizer legs | Scrub head down, tires blocked. Front tie-downs at the stabilizer legs, rear at the frame holes |
| Tennant T17 rider (9020160) | Raise squeegee, scrub head and brushes, drain tanks | Same 380 mm (15 in) rule and winch | As close to the front as possible, block each wheel, head and squeegee down, straps at the front stabilizers and rear jacking brackets |
| Tennant M17 battery sweeper-scrubber (4020655) | Raise squeegee, scrub head, brushes and hopper, drain tanks | Back it on. Ramps up to 13% (Direct Throw) or 20% (Dual Force, rear squeegee off above 13%) | Do not put the front against the trailer. Key on until straps are secure, block each wheel, lower hopper, head and squeegee |
| Tennant M20 gas/LPG sweeper-scrubber (9016000) | Drain tanks, empty hopper | Drive on, by "personnel trained on how to safely load a machine" | Parking brake, wheel blocks, head and squeegee down, straps at the front lower corners and rear jacking brackets |
| Nilfisk SC6000 rider (56091161) | "All tanks are empty" | Not stated | Doors latched, brake engaged, deck and squeegee down, then the emergency stop pressed or batteries disconnected "to prevent them from raising," key removed |
Kärcher's BD 35/15 C Classic Bp instructions add a step the others leave out: "Remove the battery from the device before transport," to prevent an uncontrolled startup, then secure the machine "against slipping and tipping over."
Four patterns run through the table.
- Empty tanks. Seven of the 11 manuals ask for drained tanks, and none says to travel with water aboard. Water is heavy: at 8.34 lb per gallon (USGS), a full 32 gal T600 solution tank adds 267 lb, which is almost exactly the gap between its 1,036 lb with batteries and its 1,304 lb GVW. Dump the recovery water at a sanitary drain before you load, as set out in where to dump floor scrubber water.
- Up to load, down to travel. Every Tennant transport procedure lowers the scrub head after the machine is in place, and the T17, M20 and SC6000 manuals say to lower the squeegee before tying down. The T600 and GeneSys manuals go further and take the squeegee off before loading, which keeps the blades off the ramp edge. A bent squeegee frame shows up later as streaks and water trails.
- Front against the bulkhead, except sweeper-scrubbers. The walk-behind manuals put the front against the front of the bed. The M17 manual says not to, because the hopper and sweeping parts "could be damaged" by contact with the trailer.
- Brakes are not enough on their own. Every Tennant procedure that mentions the parking brake also blocks the wheels. The M17 manual keeps the key on until the straps are tight, because its drive wheel dynamic brake is active when the key is on. Our wheels, tires and brakes guide explains why an electromagnetic brake is a holding brake, not a restraint for a bouncing trailer.
How many straps the federal rule requires
For cargo on a commercial motor vehicle, FMCSA sets two separate tests, and your straps have to pass both.
Count. Under 49 CFR 393.110, an article not blocked against forward movement needs one tiedown if it is 5 ft (1.52 m) long or less and 1,100 lb (500 kg) or less, and two if it is longer than 5 ft and no more than 10 ft, "irrespective of the weight." If the article is blocked forward, for example by a headerboard or bulkhead, the rule asks for one tiedown per 10 ft of length.
Strength. Under 393.106(d), the tiedowns' aggregate working load limit (WLL) must be "at least one-half times the weight of the article." Each strap that runs from the vehicle to an anchor point on the machine counts for half its WLL. A strap that goes over the machine to the other side of the vehicle counts in full.
Here is what that means for the machines above, drained and with batteries installed, not blocked forward.
| Machine | Length (manual) | Weight, tanks empty | Minimum tiedowns | Minimum aggregate WLL | Tie-down points named in the manual |
|---|---|---|---|---|---|
| Tennant T3 (smallest model) | 1,128 mm (44.4 in) | 143 kg (315 lb) | 1 | 158 lb | Straps over the top |
| Tennant T5 | 53 to 57.6 in | 580 to 629 lb | 1 | 315 lb | As shown in the manual figure |
| Tennant T600 EE | 65.8 in | 1,036 lb | 2 | 518 lb | Four brackets on the frame |
| Nilfisk SC6000 | 70 in | 1,784 lb (transportation weight) | 2 | 892 lb | Tie-down points shown in the manual |
| Tennant T16 | 74 in (99 in with pre-sweep) | 1,900 lb | 2 | 950 lb | Stabilizer legs, rear frame holes |
| Tennant M20 gas/LPG | 95 in | 3,300 lb (empty) | 2 | 1,650 lb | Front lower corners, rear jacking brackets |
| Tennant T17 | 87.9 in (113 in with pre-sweep) | 3,365 lb | 2 | 1,683 lb | Front stabilizers, rear jacking brackets |
| Tennant M17 battery | 112.8 in | 4,770 lb | 2 | 2,385 lb | Jacking bracket holes |
The weight column is our arithmetic input, the manual's "with batteries" figure, or the figure named in brackets. Our floor scrubber weight data explains why empty, battery and GVW weights differ.
Two things follow. First, strap strength runs out before strap count does. Four direct straps marked 500 lb WLL add up to 1,000 lb, enough for the T600, SC6000 and T16 but not for the T17, M20 or M17. If a strap is not marked, 393.108 tells you what to assume: 2,000 lb for 2 in synthetic webbing, 1,750 lb for 1 3/4 in. The WLL of a tiedown is also capped by the weakest part, including the anchor it hooks to, so a strong strap on a weak stake pocket counts at the stake pocket's rating. Second, on an open truck or trailer the system must also hold the machine down with "at least 20 percent of the weight of the article," per 393.102(b). The T3 manual's straps over the top of the machine, there "to prevent it from tipping," are that kind of tiedown.
Loading: ramp, winch or dock
The loading limits in these manuals are tighter than most people assume.
- Walk-behinds. The T600 manual allows only a 2 percent gradient while loading. At 2 percent, reaching a 15 in trailer deck takes a 62.5 ft ramp, so in practice that means a dock, a liftgate or a ground-level trailer. The T260 manual allows transport on inclines up to 21 percent, about ten times the T600's loading limit. Read yours.
- Riders. Tennant's T16 and T17 manuals allow driving on and off only when the loading surface "is horizontal AND 380 mm (15 in) or less from the ground." Anything higher or sloped needs a winch, chained to the stabilizer legs. The SC6000 lists a transport gradeability of 18.5 percent, and the M17 allows ramps up to 13 or 20 percent depending on the sweeping system.
To turn a percent into a ramp length for your trailer, use the table in our ramps and gradeability guide. Our rider scrubber guide covers rider sizes and weights.
Step by step
- Drain both tanks at a sanitary drain, and empty the hopper on a sweeper-scrubber.
- Raise the scrub head and squeegee, or remove the squeegee if your manual says so. Remove pads or disc brushes if the manual says to, as the T600's does.
- Load by the manual's rule: its ramp grade for walk-behinds, and the 15 in level-surface rule or a winch for Tennant riders.
- Position it. Front to the bulkhead for a walk-behind, not for a sweeper-scrubber with a front hopper. Keep it on the trailer centerline.
- Lower the scrub head and squeegee, set the parking brake, and block every wheel.
- Strap at the named points, four where the manual names four. Do not use "control console area or accessory rails for tie-down locations," as the T600 manual warns. Pad straps that cross a tank, as Betco does with a microfiber cloth.
- Secure what can move. Latch the recovery tank lid and access doors on an open bed. On the SC6000, press the emergency stop or disconnect the batteries so the deck cannot rise. Remove the key.
- Recheck the straps before you drive off and at your first stop.
Where this stops applying
- The federal rule has a scope. FMCSA's definition of a commercial motor vehicle covers vehicles used in interstate commerce with a gross vehicle or combination weight rating of 10,001 lb or more. A pickup and trailer can cross that line together. Below it, or within one state, check your state's rules, but the federal figures are still a sound yardstick.
- Lithium machines. The M17 manual says to contact Tennant or "your local regulatory authorities" before transporting the lithium-ion model. Shipping a lithium machine or pack by carrier is a hazardous materials question, covered in how to ship a floor scrubber with a lithium battery. The battery choice itself is in lithium vs lead-acid.
- Cold weather. Draining tanks before loading also helps in winter, but water still left in the pump, filter and hoses can freeze on an open trailer. The full freeze procedure is in our winterizing guide.
- Carrier and rental terms. A freight carrier or rental company may impose its own crating, battery or strapping rules. Theirs apply on top of the manual.
Frequently asked questions
Can you lay a floor scrubber down to transport it?
None of the manuals above describes transporting a scrubber on its side or back. Every procedure has the machine upright on its wheels, blocked and strapped.
Should the scrub deck be up or down during transport?
Up to load, down to travel. Every Tennant transport procedure lowers the scrub head once the machine is in place, and the SC6000 manual has you disable power so the deck cannot rise.
Can I put a walk-behind scrubber in a pickup truck?
Only if you can load it within the manual's limits. The T600 allows a 2 percent gradient while loading, which rules out a ramp to a typical pickup bed. A liftgate, dock or ground-level trailer meets it. Once loaded, block the wheels and strap it at the tie-down points.
Sources
- Tennant T600 EE Operator Manual 9016606: tennantco.com
- Tennant T5 Operator Manual 9002326: tennantco.com
- Tennant T3/T3+ Operator Manual 9004144: tennantco.com
- Tennant T260 Operator Manual TN7100012: hdsupplysolutions.com
- Betco GeneSys Mid-Size Scrubber Series Manual 92501-92, transport tie-down: betco.com
- Tennant T16 Rider Scrubber Operator Manual 9008142: thesweeper.com
- Tennant T17 Rider Scrubber Operator Manual 9020160: cloudfront.net
- Tennant M17 Battery Sweeper Scrubber Operator Manual 4020655 Rev. 9 (2-2026): tennantco.com
- Tennant M20 Gas/LPG Scrubber-Sweeper Operator Manual 9016000: tennantco.com
- Nilfisk SC6000 Instructions for Use 56091161 (4/2016): sweeperland.com
- Kärcher BD 35/15 C Classic Bp operating instructions: kaercher-media.com
- 49 CFR 393.102, minimum performance criteria for cargo securement: law.cornell.edu
- 49 CFR 393.106, general requirements for securing articles of cargo: law.cornell.edu
- 49 CFR 393.108, working load limits of tiedowns: law.cornell.edu
- 49 CFR 393.110, minimum number of tiedowns: law.cornell.edu
- 49 CFR 393.130, heavy vehicles, equipment and machinery: law.cornell.edu
- 49 CFR 390.5, definition of commercial motor vehicle: law.cornell.edu
- USGS Water Science School, A million gallons of water: how much is it?: usgs.gov