How to Remove Forklift Tire Marks From a Concrete Floor With an Auto Scrubber
Spray a high-pH tire mark remover on the marks, let it sit for several minutes, then scrub with a grit brush and pick up. Six labels compared: dose, pH, dwell, brush and floor limits.
Key takeaways
- Put a tire mark remover on the marks first, give it several minutes, then scrub and pick up. Four of the six products we read are applied to the floor before the scrubber pass, and Burn Out says it must not go in the solution tank at all.
- These are strong products. Every remover with a published pH sits at about 12 to 13 as sold, and Kärcher's RM 776 also "Removes wax and polymer coatings".
- On bare concrete, Kärcher and Burn Out both call for a grit brush on the scrubber, plus a second pass where marks are heavy. On a resin coating, Stonhard, which makes epoxy and urethane floors, names a white pad.
- Two products go in the tank instead. Betco Factory Formula HP runs from 4 oz per gallon for light soil to 26 oz per gallon for very heavy soil, and Stonhard Stonkleen TD9 runs 12 oz per gallon for normal marks and 32 oz for heavy buildup.
- A normal scrubber pass picks up its solution in 2 to 3 seconds (Tennant). To give any of these products its dwell time, put it down first or scrub once with the squeegee up.
Spray a tire mark remover onto the marks and let it sit for several minutes, then scrub the area with a grit brush on the auto scrubber and pick it all up. Where the marks are heavy, scrub a second time. That is the method printed on the Kärcher and Burn Out labels, and four of the six products we read put the chemical on the floor before the machine arrives.
Two products work from the solution tank instead, at doses far above a daily cleaner. Either way, the remover needs time on the mark, and a neutral floor cleaner with one fast pass is not what any of these makers sells for the job.
What a tire mark is, and why it needs a special product
A forklift tire mark is rubber that has rubbed off the tire and stuck to the floor, which is why Kärcher calls them "rubber abrasion marks and marks caused by forklift trucks". Delta Foremost calls the worst ones "burned-in lift-truck marks". They gather where trucks turn and brake, such as aisle ends, dock plates and charging areas, as our warehouse guide describes.
A few terms come up on every label:
- Tire mark remover. A cleaner made to soften rubber. The ones we read are either strongly alkaline (pH 12 to 13) or solvent based.
- Pre-spray. A product you put on the floor by sprayer or mop before the scrubber passes, so it sits on the mark.
- Dwell time. How long the chemical stays wet on the floor before it is picked up.
- Grit brush. A scrub brush with abrasive grit built into the nylon bristles. Our brushes and pads guide lists it for tire marks and rust, and not for finished floors.
Two answers, and which one is right
One answer says tire marks are a scrubbing problem, so you should use a neutral or mild cleaner and a tougher pad. The other says buy a strong chemical and put it in the tank. The labels say you need both, with time in between.
The chemistry side is clear. Kärcher's Tire Mark Remover is pH 12.0 to 12.8 as sold, Burn Out's Safety Data Sheet gives pH 12 to 12.8, and Kärcher's RM 776 is pH 13. Betco's Factory Formula HP is pH 12.5 as sold and 11.5 at 1:10. Delta Foremost's 722B-ES has no water in it at all, because it is a solvent blend. Not one product made for tire marks is a neutral cleaner.
The brush side is clear too. Kärcher says to use "grit" type brushes on your auto scrubber on unfinished concrete and other industrial floors. Burn Out's seller recommends a grit brush and says it means "you won't have to double scrub as often."
The step people skip is the wait, and Tennant explains why it matters. It says a normal auto scrubber pass puts solution down "and recovers it in 2-3 seconds." Kärcher asks you to "allow to work several minutes." Burn Out says to allow "several minutes to sit". Delta Foremost says to "allow to soften residue for a few minutes." So a single squeegee-down pass from the tank picks the chemical up long before the label's time is up. That gap is the likeliest reason a strong product seems to fail after one pass.
Six tire mark remover labels compared
We read the maker's data sheet or product page for each product, plus a Safety Data Sheet where we needed it.
| Product | How it goes on | Dose | pH | Dwell | Brush or pad | Floors named |
|---|---|---|---|---|---|---|
| Kärcher Tire Mark Remover and Pre-Soak | Pre-spray; auto scrubber also listed | Ready to use, or up to 1:25 for lighter duty | 12.0 to 12.8 as sold | Several minutes | Grit brush; double scrub heavy soil | Floors and other hard surfaces |
| Kärcher FloorPro RM 776 | Spray unit, then scrubber dryer | Not stated on the page | 13 | "A clear contact time" | Not stated | Industrial floors, cement screeds, epoxy |
| Burn Out (Factory Cleaning Equipment) | Pre-spray only, never in the solution tank | Dilutable, no ratio given | 12 to 12.8 (SDS) | Several minutes | Grit brush | All hard floors, epoxy, unfinished concrete |
| Delta Foremost 722B-ES Tire Burn Remover | Spread on by mop, brush or sprayer | Used as sold (contains no water) | Not stated | A few minutes | Full brush pressure, water on | Concrete and masonry |
| Betco Factory Formula HP | In the solution tank, no pre-spray | 4 to 26 oz per gallon | 12.5 as sold; 11.5 at 1:10 | Not stated | Not stated | Concrete |
| Stonhard Stonkleen TD9 | In the solution tank, or by mop | 12 oz per gallon; 32 oz heavy | Not stated | 2 to 3 minutes, concentrate on spots only | White pad for tire marks | Vinyl and other hard surfaces |
Pre-spray products
Kärcher, Burn Out, RM 776 and Delta Foremost all put the chemical on the mark first. Burn Out is the strictest, and its page says it is "not to be used directly in the solution tank of any floor cleaning machine." Kärcher's sheet lists the automatic floor scrubber among its methods, but its directions still start with "apply liberally and allow to work several minutes."
RM 776 describes a "two-step method" in which it is sprayed on, and "the dirty water is removed with a scrubber dryer after a clear contact time." Kärcher sells it for industrial floors, cement screeds and epoxy surfaces.
Delta Foremost's scrubber steps are the plainest: spread it on, let it soften the residue for a few minutes, then pick it up "with full brush pressure, water feed on, squeegee and vacuum on."
In-tank products
Betco says Factory Formula HP is "perfect for use in automatic floor scrubbers" and "requires no pre-spray on rubber tire marks." Its doses climb with the soil: 4 oz per gallon (1:32) for light soil, 8 oz (1:16) for moderate, 13 oz (1:10) for heavy and 26 oz (1:5) for very heavy.
Stonhard's TD9 sheet gives 12 oz per gallon "for normal accumulation" and 32 oz per gallon for heavy buildup, applied "with mop or auto scrubber," then a water rinse. For tire marks it recommends "a buffing machine equipped with a white scrubbing pad." The 2 to 3 minute wait is for its spot method only, where you use the product undiluted with a little water.
Neither in-tank sheet gets around the 2 to 3 second pickup, and Betco prints no dwell time. If one pass leaves marks behind, use the double scrub Kärcher prints for heavy soil: one pass with the squeegee up, a wait, then a pass with it down. Our degreasers guide walks through that double scrub step by step.
What a full tank takes
Here is our arithmetic for a 12 gallon solution tank, the size of a mid-size walk-behind.
| Product and dose | For 12 gallons |
|---|---|
| Betco Factory Formula HP, light (4 oz per gallon) | 48 oz |
| Betco Factory Formula HP, heavy (13 oz per gallon) | 156 oz (about 1.2 gallons) |
| Betco Factory Formula HP, very heavy (26 oz per gallon) | 312 oz (about 2.4 gallons) |
| Stonkleen TD9, normal (12 oz per gallon) | 144 oz |
| Stonkleen TD9, heavy (32 oz per gallon) | 384 oz (3 gallons) |
These are not daily cleaner doses, since a heavy TD9 mix is one part chemical to four parts water. Measure the real fill, not the size on the nameplate. Our dilution ratio guide has the math for labels that give only a ratio.
A worked example: one dock aisle on bare concrete
Take a dock aisle in a distribution center, with bare concrete that has no sealer and black marks where trucks turn off the dock plate. The machine is a walk-behind disc scrubber, and here is how the labels would have you run it.
- Sweep first. Dock grit and wrap damage brushes and fill the recovery tank, as our warehouse guide explains.
- Fit the grit brush. Kärcher and Burn Out both name it for unfinished concrete.
- Spray the marks. Suppose you use Kärcher's Tire Mark Remover as sold, since these are heavy marks and the 1:25 dilution is for lighter duty.
- Wait several minutes. Spray only as much floor as you can scrub when that time is up.
- Scrub and pick up. Run the scrubber over the sprayed patch with the squeegee down. Overlap your passes, as both labels ask.
- Scrub again where marks remain. Kärcher says to "double scrub" when heavy soil is present.
Now suppose you would rather use Betco from the tank. Heavy soil calls for 13 oz per gallon, so a 12 gallon tank takes 156 oz of product. Scrub the marked zone once with the squeegee up, wait, then scrub again with it down. Afterward, flush the solution system with clean water, so a pH 12 product does not sit in the pump and lines.
Which method for which floor
This table restates the rulings above, and each row names its source.
| Floor | Chemical | Tool | Source |
|---|---|---|---|
| Bare or unfinished concrete | High-pH pre-spray, or Betco in the tank | Grit brush, double scrub heavy marks | Kärcher, Burn Out, Betco |
| Epoxy or other resin coating | RM 776 or Burn Out, both list epoxy | White pad | Kärcher, Burn Out, Stonhard |
| Finished floor (wax or polymer finish) | Expect the remover to take finish off | Plan to recoat the area | Kärcher RM 776, Burn Out |
| Polished concrete | None of the six labels names it | See our polished concrete guide | None |
On coatings, the grit brush is the part to drop. Kärcher's and Burn Out's grit brush advice is written for unfinished concrete. Stonhard makes epoxy and urethane floors, and its own tire mark step uses a white pad. Our epoxy floors guide lists grit brushes among the tools to avoid on smooth, high-gloss epoxy.
Where this answer stops applying
- Floor finish. Kärcher says RM 776 "removes wax and polymer coatings." Burn Out tells you to test it in a small area first "to make sure it does not harm your floor finish." On a finished floor, treat tire mark removal as spot stripping and plan to recoat. Our stripping guide covers that job.
- Polished concrete. None of the six labels names it. Check with whoever polished the floor before you put a pH 12 product or a grit brush on it, because both are outside every label here. Our polished concrete guide covers daily care.
- Machines that ban solvents. Delta Foremost's 722B-ES contains chlorinated solvent and is a flammable liquid. The IPC CT15 family manual says never to use or pick up flammable liquids or solvents "even if diluted." If your manual says the same, a solvent product does not go through the machine.
- Squeegee blades. Burn Out's SDS lists d-limonene and 2-butoxyethanol. Our squeegee blade guide notes that solvent and citrus products can attack natural rubber blades.
- People. RM 776 "causes severe skin burns and eye damage." Read the SDS before you open the container, and wear the gloves and eye protection it names.
- Products we could not verify. We looked for tire mark products from Spartan, Zep and NCL and found no data sheet that names tire marks. A UK sheet from Clemas would not load. None is in the table.
Frequently asked questions
What is the best way to remove forklift tire marks from concrete?
Spray a high-pH tire mark remover on the marks, wait several minutes, then scrub with a grit brush and pick up. Scrub again where marks are heavy, which is the method on the Kärcher and Burn Out labels.
Can I put tire mark remover in my scrubber's solution tank?
Only if the label says so. Burn Out says never. Betco Factory Formula HP and Stonhard Stonkleen TD9 are made to go in the tank, at 4 to 26 oz and 12 to 32 oz per gallon.
Will tire mark remover damage floor finish?
It can. Kärcher says RM 776 removes wax and polymer coatings, and Burn Out says to test first so it does not harm your finish. On a finished floor, plan to recoat the area you treat.
Why didn't my degreaser get the tire marks off?
Most likely it was picked up too fast. A normal pass recovers solution in 2 to 3 seconds, while the labels ask for several minutes, so pre-spray the marks or scrub once with the squeegee up.
Sources
- Kärcher, Tire Mark Remover and Pre-Soak product sheet (07/2021): saleslayer.com
- Kärcher, FloorPro Tyre and Abrasion Marks Remover RM 776 (6.295-545.0): karcher.com
- Factory Cleaning Equipment, Burn Out Tire Mark Remover product page: thesweeper.com
- Factory Cleaning Equipment, Burn Out flyer: thesweeper.com
- Factory Cleaning Equipment, Burn Out Safety Data Sheet (6/13/2025): thesweeper.com
- Delta Foremost, 722B-ES Tire Burn Remover brochure and technical data (Rev. 7-30-15): deltaforemost.com
- Betco, Factory Formula HP Cleaner/Degreaser product page: betco.com
- Stonhard, Stonkleen TD9 product data (05/25): stonhard.com
- Stonhard, home page (seamless epoxy, urethane and MMA flooring): stonhard.com
- Tennant, Quick Tips for Cleaning and Disinfecting Floors: tennantco.com
- IPC, CT15, CT15R, CT30, CT45, CT46 Operations Manual: ipcworldwide.com